You are here: CSP Developer’s Guide: Common Channel Signaling > 7 SS7 PPL Information > ISUP SPRC (0x0013)
Purpose
This section includes ITU and ANSI PPL Config Bytes, all PPL Events, and Timer information for the PPL Component ISUP SPRC.
ISUP SPRC Configuration Bytes (ITU)
You can modify the parameters for Config Bytes 1–4, but you cannot move them to other byte locations. Other functions in the system access these parameters.
Byte |
Description |
Value |
---|---|---|
0x01 |
Parameter ID |
0x16 (Range and Status) |
0x02 |
Byte offset of range field |
0x00 |
0x03 |
Service Indicator |
0x05 |
0x04 |
Subservice Field |
0x02 |
0x05 |
0x00 Disable [default] 0x01 Enable |
|
0x06–0x09 |
Unused |
|
Confusion (CFN) for MCP |
||
0x0A |
Information Length |
0x06 |
0x0B |
Message ID |
0x2F (CFN) |
0x0C |
Parameter Count |
0x01 |
0x0D |
Parameter 1 ID |
0x12 (Cause Indicators) |
0x0E |
Parameter 1 Length |
0x02 |
0x0F |
Parameter 1 Data[0] |
0x80 (Location=User) |
0x10 |
Parameter 1 Data[1] |
0xE1 (Cause 97=Protocol Error, Message Type Not Implemented) |
0x11–0x13 |
Not Used |
|
|
|
|
Unequipped CIC (UCIC) |
||
0x1E |
Information Length |
0x02 |
0x1F |
Message ID |
0x2E (UCIC) |
0x20 |
Parameter Count |
0x00 |
0x21–0x27 |
Not Used |
|
0x28 |
Enable/Disable ACC Local Overload Algorithm |
0x01=Enabled |
0x29 |
Outstanding QueueProbe Count for ACL0 Low Level |
0x00 |
0x2A |
Outstanding QueueProbe Count for ACL0 High Level |
0x04 |
0x2B |
Outstanding QueueProbe Count for ACL1 High Level |
0x03 |
0x2C |
Outstanding QueueProbe Count for ACL1 High Level |
0x0B |
0x2D |
Outstanding QueueProbe Count for ACL2 Low Level |
0x09 |
0x2E |
Outstanding QueueProbe Count for ACL2 Low Level |
0x0B |
0x2F |
Congestion Cleared Threshold for Outgoing Calls, 100 ms units |
10 ms 0x0A |
0x30 |
Number of probes to determine congestion cleared=Outgoing Calls |
10 0x0A |
0x31 |
Defines the range of channels in GRS |
0x0C (Default value or indicates maximum number of CICs per span) |
0x32 |
Defines whether purging is on or off in the case of CCS redundancy loss. |
0x01 Enabled |
Unrecognized Message Processing |
||
0x3D |
Message Compatibility Parameter (MCP) Processing Notification |
0x00=Do Not send PPL Event to Host 0x01=Send PPL Event to Host |
0x3E |
Unrecognized Parameter Pass On |
0x00=Pass On Not Possible 0x01=Pass On Is Possible |
Release (REL) for Message Not Supported |
||
0x42 |
CGRS stop upon receipt of UCIC |
0x00 = Stop 0x01 = Do not stop (Default) |
0x46 |
Information Length |
0x06 |
0x47 |
Message ID |
0x0C (REL) |
0x48 |
Parameter Count |
0x01 |
0x49 |
Parameter 1 ID |
0x12 (Cause Indicators) |
0x4A |
Parameter 1 Length |
0x02 |
0x4B |
Parameter 1 Data [0] |
0x80 (Location=User) |
0x4C |
Parameter 1 Data [1] |
0xE1 (Cause 97=Message Type Not Implemented) |
ISUP Automatic Congestion Control (ACC) |
||
0x50 |
Multiplicative Decrement Constant Beta_0 normalized to 128 |
0x80 |
0x51 |
Multiplicative Decrement Constant Beta_1 |
0x80 |
0x52 |
Multiplicative Decrement Constant Beta_2 |
0x80 |
0x53 |
Multiplicative Decrement Constant Beta_3 |
0x80 |
0x54 |
Multiplicative Decrement Constant Beta_4 |
0x7A |
0x55 |
Multiplicative Decrement Constant Beta_5 |
0x76 |
0x56 |
Multiplicative Decrement Constant Beta_6 |
0x6E |
0x57 |
Multiplicative Decrement Constant Beta_7 |
0x64 |
0x58 |
Multiplicative Decrement Constant Beta_8 |
0x5A |
0x59 |
Multiplicative Decrement Constant Beta_9 |
0x5A |
0x5A |
Multiplicative Decrement Constant Beta_10 |
0x50 |
0x5B |
Multiplicative Decrement Constant Beta_11 |
0x32 |
0x5C |
Multiplicative Decrement Constant Beta_12 |
0x28 |
0x5D |
Multiplicative Decrement Constant Beta_13 |
0x1E |
0x5E |
Multiplicative Decrement Constant Beta_14 |
0x0A |
0x5F |
Multiplicative Decrement Constant Beta_15 |
0x00 |
0x60 |
Additive Increase Constant - Alpha |
0x02 |
0x61 |
Maximum Residual delay of a Queue Probe |
0x64 |
0x62 |
Accuracy Limit |
0x80 |
0x90 |
ACL0 Low Level Offset for CPU Utilization |
0x5A |
0x91 |
ACL0 High Level Offset for CPU Utilization |
0x55 |
0x92 |
ACL1 Low Level Offset for CPU Utilization |
0x53 |
0x93 |
ACL1 High Level Offset for CPU Utilization |
0x5B |
0x94 |
ACL2 Low Level Offset for CPU Utilization |
0x58 |
0x95 |
ACL2 High Level Offset for CPU Utilization |
0x5F |
0x8C |
Type of STACK |
0x00=Non-BT Stack(default) 0x01=BT Stack |
0x8D |
CS ACL2 Fraction Allowed |
0x20 |
Release (REL) for INF Timer Expiration |
||
0x6E |
Information Length |
0x06 |
0x6F |
Message ID |
0x0C (REL) |
0x70 |
Parameter Count |
0x01 |
0x71 |
Parameter 1 ID |
0x12 |
0x72 |
Parameter 1 Length |
0x02 |
0x73 |
Parameter 1 Data [0] |
0x80 (Location=User) |
0x74 |
Parameter 1 Data [1] |
0x9F (Cause 31=Normal Unspecified) |
0x75–0xC8 |
Unused |
|
ISUP SPRC PPL Event Indications (ITU)
Event ID |
Event |
---|---|
0x01 |
Format error in incoming message (NOTE: The PPL Event Indication has AIB of stack) |
0x02 |
Unequipped CIC in incoming message (NOTE: The PPL Event Indication has an AIB of stack) |
0x03 |
Undefined message received (NOTE: The PPL Event Indication has an AIB of stack) |
0x04 |
Confusion Message received (NOTE: The PPL Event Indication will have a AIB of span/channel) |
0x05 |
Remote User Part Available (NOTE: The PPL Event Indication has AIB of channel) |
0x06 |
Pass On unrecognized/unexpected message |
0x07 |
Unrecognized message received on unequipped CIC |
ISUP CPC PPL Timers (ITU)
Timer ID |
Timer |
Default Value (10ms) |
---|---|---|
0x01 |
MTP Pause timer base (pause expiration is 10 times this value) |
400 |
0x02 |
Queue Probe Timer |
10 |
ISUP SPRC Configuration Bytes (ANSI)
You can modify the parameters for Config Bytes 1–4, but you cannot move them to other byte locations. Other functions in the system access these parameters.
Byte |
Description |
Value |
---|---|---|
0x01 |
Parameter ID |
0x16 (Change and Status) |
0x02 |
Byte offset of range field |
0x00 |
0x03 |
ANSI Service Indicator |
0x05 |
0x04 |
ANSI Network Indicator |
0x02 |
0x05 |
MTP Pause Logic Flag |
0x00 Disable [default] 0x01 Enable |
Confusion (CFN) for Message Type Unknown |
||
0x06 |
Information Length |
0x06 |
0x07 |
Message ID |
0x2F (CFN) |
0x08 |
Parameter Count |
0x01 |
0x09 |
Parameter 1 ID |
0x12 (Cause Indicators) |
0x0A |
Parameter 1 Length |
0x02 |
0x0B |
Parameter 1 Data[0] |
0x80 (Location=User) |
0x0C |
Parameter 1 Data[1] |
0xE1 |
0x0D-0F |
Not Used |
|
Confusion (CFN) for Protocol Error |
||
0x14 |
Information Length |
0x06 |
0x15 |
Message ID |
0x2F (CFN) |
0x16 |
Parameter Count |
0x01 |
0x17 |
Parameter 1 ID |
0x12 (Cause Indicators) |
0x18 |
Parameter 1 Length |
0x02 |
0x19 |
Parameter 1 Data[0] |
0x80 (Location=User) |
0x1A |
Parameter 1 Data[1] |
0xEF |
0x1B–0x1D |
Unused |
0x00 |
Unequipped CIC (UCIC) |
||
0x1E |
Information Length |
0x02 |
0x1F |
Message ID |
0x2E |
0x20 |
Parameter Count |
0x00 |
0x21–0x27 |
Unused |
|
0x28 |
Number of probes to determine Average Delay |
10 |
0x29 |
Probe Delay Threshold for Incoming Calls, 100 ms units |
100 ms |
0x2A |
Average Delay Threshold for Incoming Calls, 100 ms units |
50 ms |
0x2B |
Congestion Cleared Threshold for Incoming Calls, 100 ms units |
10 ms |
0x2C |
Number of probes to determine congestion cleared=Incoming Calls |
10 |
0x2D |
Probe Delay Threshold for Outgoing Calls, 100 ms units |
100 ms |
0x2E |
Average Delay Threshold for Outgoing Calls, 100 ms units |
50 (5 s) |
0x2F |
Congestion Cleared Threshold for Outgoing Calls, 100 ms units |
10 (1 s) |
0x30 |
Number of probes to determine congestion cleared=Outgoing Calls |
10 |
0x31 |
Defines the range of channels in GRS |
0xFF (Default value or indicates maximum number of CICs per span) |
0x32 |
Defines whether purging is on or off in the case of CCS redundancy loss. |
0x01 Enabled |
Circuit Validation Response (CVR) |
||
0x32 |
Information Length |
0x08 |
0x33 |
Message ID |
0xEB |
0x34 |
Parameter Count |
0x02 |
0x35 |
Parameter 1 ID |
0xE6 (CVR) |
0x36 |
Parameter 1 Length |
0x01 |
0x37 |
Parameter 1 Data[0] |
0x01 |
0x38 |
Parameter 2 ID |
0xE5 (CGC) |
0x39 |
Parameter 2 Data Length |
0x01 |
0x3A |
Parameter 2 Data[0] |
0x01 |
0x3C |
Exchange Type |
0x00=Type A 0x01=Type B (default) |
0x3D–0x6D |
Not Used |
|
Release (REL) (INF Timer Expiry) |
||
0x6E |
Information length |
0x06 |
0x6F |
Message ID |
0x0C |
0x70 |
Parameter Count |
0x01 |
0x71 |
Parameter 1 ID |
0x12 |
0x72 |
Parameter 1 Length |
0x02 |
0x73 |
Parameter 1 Data [0] |
0x80 (Location=User) |
0x74 |
Parameter 1 Data [1] |
0x9F (Temp Failure) |
0x75–0xC8 |
Unused or User-defined |
|
ISUP SPRC PPL Event Indications (ANSI)
Event ID |
Event |
---|---|
0x01 |
Format error in incoming message (NOTE: The PPL Event Indication will have a AIB of stack) |
0x02 |
Unequipped CIC in incoming message (NOTE: The PPL Event Indication has an AIB of stack unless the incoming DPC is not configured. In that case, a Channel AIB with data of 0xFF FF FF is used.) |
0x03 |
Undefined message received (NOTE: The PPL Event Indication will have a AIB of stack) |
0x04 |
Confusion Message received (NOTE: The PPL Event Indication will have a AIB of span/channel) |
ISUP SPRC PPL Timers (ANSI)
Timer ID |
Timer |
Default Value (10ms) |
---|---|---|
0x01 |
MTP Pause timer base (pause expiration is 10 times this value) |
400 |
0x02 |
Time between probes for Congestion Control |
100 |