E-ONE 120 Ohm I/O Card - Model No. EXSEIO1000

You are here: Excel CSP Hardware Product Descriptions > 3 Line Cards > E-ONE 120 Ohm I/O Card - Model No. EXSEIO1000

The E-ONE 120 Ohm I/O card connects the CSP to E1 lines and other telecommunications equipment.

Use only 120 Ohm impedance shielded twisted-pair cable in compliance with UTI G.703. Do not use flat wire. Wire the interface connection in accordance with ANSI 50-position RJ48M pinout specifications.

The E-ONE 120 Ohm I/O card resides in the rear card slots of a CSP 2090, CSP 2110 or CSP 2040 chassis.

The part number, serial number, model number, and revision are located on the back of the board.

The E-ONE 120 Ohm I/O card is designed to the following electrical, physical and environmental specifications.

The E-ONE 120 Ohm I/O card complies with all relevant regulations from the following standards organizations and governing bodies.

A digital communications link - voice, data, and video at a 2.048 Mbps rate; 30B/2D or 31B/1D (ISDN); non-North American version of T1.

Electrical	Specification
Supply Voltage, Vcc	5.00V
Supply Current, Vcc @ 5.0V	0.95A (typical)

Physical	Specification
Height	318.5 mm (12.54 in.)
Depth	105.2 mm (4.14 in)
Width	19.7 mm (0.775 in.)

Environmental	Specification
Temperature - Storage	-40~C to 70~C (-40~F to 158~F)
Temperature - Operation	0~C to 50~C (32~F to 122~F)
Temperature Shock - Storage	-40~C to 70~C to -40~C (-40~F to 158~F to -40~F) @ 5~C/min.
Temperature Shock - Operation	0~C to 50~C (32~F to 122~F) @ 10~C/min.
Humidity - Operating	5% to 85%
Altitude	Up to 4000 m (13,123 ft.)

Country/Standards Organization	Regulations
United States	FCC Part 15 CSA 60950-1-3
Canada	ICES 003 CSA 60950-1-3
NEBS	Level 3
European Union	CE Mark 120 Ohm: CTR 12 Compliant
Switzerland	BAKOM

Product	Model No.
E-ONE Card	EXS-E1C-1160
E-ONE 120 Ohm Redundant I/O Card	EXS-EIO-1200
E-ONE 120 Ohm Standby I/O Card	EXS-EIO-1300

16 Span I/0 Pinout
No.	Tip	Ring	Tip	Ring
Connector A
0	27	2	26	1
1	30	5	29	4
2	33	8	32	7
3	36	11	35	10
4	39	14	38	13
5	42	17	41	16
6	45	20	44	19
7	48	23	47	22
Connector B
8	27	2	26	1
9	30	5	29	4
10	33	8	32	7
11	36	11	35	10
12	39	14	38	13
13	42	17	41	16
14	45	20	44	19
15	48	23	47	22

American National Standards Institute. ANSI administers and coordinates the U.S. voluntary standardization and conformity assessment system for the
telecommunications industry. More details on these standards may be
viewed at www.ansi.org.

See Converged Services Administrator.

An I/O card that supports redundancy and has external connections. It sits behind whichever line card is originally designated as "active." Compare to "Standard I/O card" and "Standby I/O card."

An I/O card that supports redundancy but has no external connections. A Standby I/O card sits behind whichever line card is originally designated as "standby." Compare to "Redundant I/O card" and "Standard I/O card."

Range of channels provided by T1 or E1 transmission service. A physical span is a group of channels taking up a single physical wire. A logical span is a group of channels taking up less than a single logical wire, or carried over more than one physical wire.

16 Span I/0 Pinout
Span	Transmit		Receive
No.	Tip	Ring	Tip	Ring
Connector A
0	27	2	26	1
1	30	5	29	4
2	33	8	32	7
3	36	11	35	10
4	39	14	38	13
5	42	17	41	16
6	45	20	44	19
7	48	23	47	22
Connector B
8	27	2	26	1
9	30	5	29	4
10	33	8	32	7
11	36	11	35	10
12	39	14	38	13
13	42	17	41	16
14	45	20	44	19
15	48	23	47	22