You are here: Excel CSP Hardware Product Descriptions > 6 Resource Cards > DSP Series 2 Card - CSP-DSP-1310 and CSP-DSP-1320

DSP Series 2 Card - CSP-DSP-1310 and CSP-DSP-1320

Description

You can order the DSP Series 2 card with either one or two DSP modules. The one-module card is the CSP-DSP 1310. The two-module card is the CSP-DSP 1320. Each module consists of four DSP chips, for a total of either four or eight DSP chips per card. Each DSP chip has access to 512 timeslots of PCM. The 512 timeslots are arranged in two streams of 256 timeslots each. Each DSP is controlled through a host port interface mapped into the main board’s memory space.

The DSP Series 2 card main board has 128 Mbyte of external synchronous SDRAM and 2 MBytes of Flash memory. The processor is a HIP4 8260 running at 83 Mhz.

Ethernet Switch

The main board has an internal Ethernet switch, and brings out three external 100 Base-T Ethernet ports to the I/O. These three ports can be used for redundancy.

Function

The DSP Series 2 card can perform a single function or a combination of the following functions:

• Tone generation

• Tone detection

• Conferencing

• File Playback/Record

• Signal energy detection

Placement

The DSP Series 2 card resides in the front slot of the following CSP chassis:

CSP 2040

Two fully-loaded DSP-2 cards can operate in an CSP 2040 Chassis.

CSP 2090 and CSP 2110

Five fully-loaded DSP-2 cards can operate in the CSP 2090 and CSP 2110 chassis.

 

Configuration Information

The part number, serial number, model number, and revision number are located on the back of the card.

Specifications

The DSP Series 2 card is designed to the following electrical, physical, and environmental specifications.

Electrical

Specification

Supply Voltage, Vcc

5.00V

Supply Current, Vcc @ 5.0V

5.5A (typical)

Physical

Specification

Height

9.3 inches (236.2 mm)

Depth

12.5 inches (317.5 mm)

Width

.775 inches (19.7 mm)

Environmental

Specification

Temperature - Storage

-40~C to 70~C (-40~F to 158~F)

Temperature - Operation

0~C to 50~C (32~F to 122~F)

Temperature Shock - Storage

-40~C to 70~C to -40~C (-40~F to 158~F to -40~F) at 5~C/min.

Temperature Shock - Operation

0~C to 50~C (32~F to 122~F) at 10~C/min.

Humidity - Operating

5% to 85%

Altitude

Up to 1824 meters (6000 ft.)

 

 

Power Requirements

Configuration

Min. Current
at 5V

Max Current
at 5V

Minimum
Power

Maximum
Power

DSP Series 2 with one
Module

4.2

4.4

21.0

22.0

DSP Series 2 with two Modules

5.2

5.5

26.0

27.5

Compliance

The DSP Series 2 card complies with all relevant regulations from the following standards organizations and governing bodies.

Country/Standards Organization

Regulations

United States and Canada

FCC Part 15 and ICES 003, Class A
CSA 60950-1-3 and CB Scheme (all country deltas)

NEBS

Pending:
NEBS Level 3
(GR-1089-CORE, GR-63-Core)

European Union (CE Mark)

CISPR 22, Class A
EN 55022, EN 55024
EN 300 386
EN 60950, EN 41003-1
G.703, G.704

DSP Series 2 Card Models

The available DSP Series 2 card models are listed below.

Product

Model No.

DSP Series 2 with (1) Module

CSP-DSP 1310

DSP Series 2 with (2) Modules

CSP-DSP 1320

Related Products

The products related to the DSP Series 2 card are listed below.

Product

Model No.

Multi-Function Media I/O

CSP-BIO-1000

Front and Top Views

The front and side views show the LEDs, push button switches, Monitor connector, DIP switches, and jumpers.

Controls and Indicators

The table below describes the LEDs and push button switches as shown in the front view of the DSP Series 2 card.

Status Indicators

LED indicators reference standard CPU run/halt/reset statuses.

LED

Color/Status

Description

Diag

Off

This LED is OFF except during a card reset, when this card flashes red briefly.

Status

Red

The LED is red briefly during card reset.

Green

The card is connected to the system buses.

Off

The card is resetting.

Halt

Red

The CPU has halted. This LED is red briefly during card reset.

Green

The CPU is running.

Power

Red

The LED is red upon insertion

Green

The card is In Service.

Off

The card is Out Of Service.

 

Jumpers

The table below indicates the jumper settings.

Jumper

Setting

Description

J1009

Installed (default)

Factory use only

J1010

Installed (default)

Factory use only

J1011

Installed (default)

Factory use only

J1013

Not Installed (default)

Factory use only

J1014

Not Installed (default)

Factory use only

J1015

Not Installed (default)

Factory use only

GJ1000

Not Installed (default)

Factory use only

DIP Switch S1 on Main Board

The table below describes the DIP switch S1 settings. The shading (asterisk* for html documents) indicates factory-installed settings.

Position

Setting

Function

1

ON*

Disables Debug 1 Mode

OFF

Enables Debug 1 Mode ( printing)

2

ON*

Reserved, normally should be ON

OFF

Reserved

3

ON*

Disables Debug 2 Mode

OFF

Enables Debug 2 Mode

4

ON*

Reserved, normally should be ON

OFF

Reserved

5

ON*

Reserved, normally should be ON

OFF

Reserved

6

ON*

Reserved, normally should be ON

OFF

Reserved

7

ON*

Reserved, normally should be ON

OFF

Reserved

8

ON*

Reserved, normally should be ON

OFF

Reserved