E1 PPL Component Information (0x0001)

You are here: CSP Developer’s Guide: Line Cards > 3 E1 Information > E1 PPL Component Information (0x0001)

Events

The events listed below are specific to the E1 PPL component.

Events 0-15 are Receive Line Signaling Events. They require an Event Data value for the Timer Filter. The data value is an index into the Generic Protocol Timer list that is configurable using the PPL Timer Configure message.

The default value for timers 1-45 are shown below in 10 millisecond units. Timers 46-100 are not used. See the default E1 PPL DSD for the default timers used for each event.

Table 3-1 E1 Events

0	RCV LINE SIG 0000	Receive CAS line signaling bits of a = 0, b = 0, c = 0, d=0.
0	RCV LINE SIG 0000	Event Data: Index Into Generic Protocol Timer List for Filter Value
1	RCV LINE SIG 0001	Receive CAS line signaling bits of a = 0, b = 0, c = 0, d=1.
1	RCV LINE SIG 0001	Event Data: Index Into Generic Protocol Timer List for Filter Value
2	RCV LINE SIG 0010	Receive CAS line signaling bits of a = 0, b = 0, c = 1, d=0.
2	RCV LINE SIG 0010	Event Data: Index Into Generic Protocol Timer List for Filter Value
3	RCV LINE SIG 0011	Receive CAS line signaling bits of a = 0, b = 0, c = 1, d=1.
3	RCV LINE SIG 0011	Event Data: Index Into Generic Protocol Timer List for Filter Value
4	RCV LINE SIG 0100	Receive CAS line signaling bits of a = 0, b = 1, c = 0, d=0.
4	RCV LINE SIG 0100	Event Data: Index Into Generic Protocol Timer List for Filter Value
5	RCV LINE SIG 0101	Receive CAS line signaling bits of a = 0, b = 1, c = 0, d=1.
5	RCV LINE SIG 0101	Event Data: Index Into Generic Protocol Timer List for Filter Value
6	RCV LINE SIG 0110	Receive CAS line signaling bits of a = 0, b = 1, c = 1, d=0.
6	RCV LINE SIG 0110	Event Data: Index Into Generic Protocol Timer List for Filter Value
7	RCV LINE SIG 0111	Receive CAS line signaling bits of a = 0, b = 1, c = 1, d=1.
7	RCV LINE SIG 0111	Event Data: Index Into Generic Protocol Timer List for Filter Value
8	RCV LINE SIG 1000	Receive CAS line signaling bits of a = 1, b = 0, c = 0, d=0.
8	RCV LINE SIG 1000	Event Data: Index Into Generic Protocol Timer List for Filter Value
9	RCV LINE SIG 1001	Receive CAS line signaling bits of a = 1, b = 0, c = 0, d=1.
9	RCV LINE SIG 1001	Event Data: Index Into Generic Protocol Timer List for Filter Value
10	RCV LINE SIG 1010	Receive CAS line signaling bits of a = 1, b = 0, c = 1, d=0.
10	RCV LINE SIG 1010	Event Data: Index Into Generic Protocol Timer List for Filter Value
11	RCV LINE SIG 1011	Receive CAS line signaling bits of a = 1, b = 0, c = 1, d=1.
11	RCV LINE SIG 1011	Event Data: Index Into Generic Protocol Timer List for Filter Value
12	RCV LINE SIG 1100	Receive CAS line signaling bits of a = 1, b = 1, c = 0, d=0.
12	RCV LINE SIG 1100	Event Data: Index Into Generic Protocol Timer List for Filter Value
13	RCV LINE SIG 1101	Receive CAS line signaling bits of a = 1, b = 1, c = 0, d=1.
13	RCV LINE SIG 1101	Event Data: Index Into Generic Protocol Timer List for Filter Value
14	RCV LINE SIG 1110	Receive CAS line signaling bits of a = 1, b = 1, c = 1, d=0.
14	RCV LINE SIG 1110	Event Data: Index Into Generic Protocol Timer List for Filter Value
15	RCV LINE SIG 1111	Receive CAS line signaling bits of a = 1, b = 1, c = 1, d=1.
15	RCV LINE SIG 1111	Event Data: Index Into Generic Protocol Timer List for Filter Value
16	FWD R2 SIG1	Receive multifrequency forward R2 signal 1.
17	FWD R2 SIG2	Receive multifrequency forward R2 signal 2.
18	FWD R2 SIG3	Receive multifrequency forward R2 signal 3.
19	FWD R2 SIG4	Receive multifrequency forward R2 signal 4.
20	FWD R2 SIG5	Receive multifrequency forward R2 signal 5.
21	FWD R2 SIG6	Receive multifrequency forward R2 signal 6.
22	FWD R2 SIG7	Receive multifrequency forward R2 signal 7.
23	FWD R2 SIG8	Receive multifrequency forward R2 signal 8.
24	FWD R2 SIG9	Receive multifrequency forward R2 signal 9.
25	FWD R2 SIG10	Receive multifrequency forward R2 signal 10.
26	FWD R2 SIG11	Receive multifrequency forward R2 signal 11.
27	FWD R2 SIG12	Receive multifrequency forward R2 signal 12.
28	FWD R2 SIG13	Receive multifrequency forward R2 signal 13.
29	FWD R2 SIG14	Receive multifrequency forward R2 signal 14.
30	FWD R2 SIG15	Receive multifrequency forward R2 signal 15.
31	BWD R2 SIG1	Receive multifrequency backward R2 signal 1.
32	BWD R2 SIG2	Receive multifrequency backward R2 signal 2.
33	BWD R2 SIG3	Receive multifrequency backward R2 signal 3.
34	BWD R2 SIG4	Receive multifrequency backward R2 signal 4.
35	BWD R2 SIG5	Receive multifrequency backward R2 signal 5.
36	BWD R2 SIG6	Receive multifrequency backward R2 signal 6.
37	BWD R2 SIG7	Receive multifrequency backward R2 signal 7.
38	BWD R2 SIG8	Receive multifrequency backward R2 signal 8.
39	BWD R2 SIG9	Receive multifrequency backward R2 signal 9.
40	BWD R2 SIG10	Receive multifrequency backward R2 signal 10.
41	BWD R2 SIG11	Receive multifrequency backward R2 signal 11.
42	BWD R2 SIG12	Receive multifrequency backward R2 signal 12.
43	BWD R2 SIG 13	Receive multifrequency backward R2 signal 13.
44	BWD R2 SIG 14	Receive multifrequency backward R2 signal 14.
45	BWD R2 SIG 15	Receive multifrequency backward R2 signal 15.
46	R2 COMP CYCLE COMPLETE	Generated upon R2 cycle completion when indicated by the Generate Call Processing Event of BWD R2 Compelled Signal with Cycle Completion.
50	L5 BUSY OUT	L4-initiated Busy Out event.
51	L5 BUSY OUT RELEASE	L4-initiated Release Busy Out event.
55	L4 CALL REQ	Outgoing call request generated by L4 when a Connect message is sent from L5 and the B party is in the idle state.
56	L4 ALERTING	L4 indication sent to the PPL on an incoming call when the destination is being rung.
57	L4 CONNECT	L4 indication sent to the PPL on an incoming call when the destination has answered.
58	L4 CLEAR REQ	L4 indication to release the call or L4 ACK to a L3 "Disconnect".
59	L4 BUSY OUT ACK	L4 ACK to L3 "Busy Out" message.
60	L4 PURGE	L4-initiated purge event.
61	L4 OUTSEIZE CONTROL	L4 Outseize Control message event.
62	L4 INSEIZE CONTROL	L4 Inseize Control message event.
66	DSP RESULT DIGITS	Generated upon detection of DTMF digits.
67	DSP RESULT FIRST-DIGIT TIMEOUT	Generated upon failure to detect DTMF digit.
68	DSP RESULT INTER-DIGIT TIMEOUT	Generated upon detecting DTMF inter-digit timeout.
69	DSP RESULT DIGITS COMPLETE TIMEOUT	Generated upon failure to detect a complete set of DTMF digits.
70	DSP RESULT OUTPULSE COMPLETE	Generated upon DTMF digit outpulsing completion.
71	L3PPLevDSP_RESULT_CP_RESUL.	Generated when DSP reports a call progress analysis result.
72	DSP Result Dialtone Detected	Generated upon detection of dial tone.
80	DSP Announcement Start	Generated by the beginning of a recorded announcement.
81	DSP Announcement Complete	Generated by the completion of a recorded announcement.

Table 3-2 E1 PPL Timers

Timer Number	Description	Default Value (in 10 ms units)
1	(S19) Incoming Layer 4 busy out Acknowledge wait	400
2	(S2) Incoming Stage 1 FWD digit receive wait	2,000
3	(S3) Incoming Stage 2 FWD digit receive wait	2,000
4	(S4) Incoming Stage 3 FWD digit receive wait	2,000
5	(S5) Incoming Stage 4 FWD digit receive wait	2,000
6	(S13) Layer 4 Connect wait	24,000
7	(S14) Layer 4 Clear wait	400
8	(S21) Clear Forward (idle line signal) wait	1,500
9	(S3) Incoming Stage 2 Initial FWD digit receive wait	2,000
10	(S2) Incoming Stage 1 Initial FWD digit receive wait	2,000
11	(S5) Incoming Stage 4 Initial FWD digital receive wait	2,000
12	(S4) Incoming Stage 3 Initial FWD digit receive wait	2,000
13	(S15) Layer 3 Circuit Release wait	10
14	(S18) Layer 3 Circuit Release wait	10
15	(S6) Host Control wait	6,000
16	(S13) Layer 4 Connect wait	24,000
17	(S29) Seize Acknowledge wait	400
18	(S31) After detecting glare time to wait before transmitting idle signal	10
19	(S32) Time to wait before looking for idle line signal after transmitting idle signal when glare detected	10
20	(S39) Outgoing Stage 1 BWD R2 signal wait	1,500
21	(S39) Outgoing Stage 1 Initial BWD R2 signal wait	1,500
22	(S41) Outgoing Stage 2 BWD R2 signal wait	1,500
23	(S41) Outgoing Stage 2 Initial BWD R2 signal wait	1,500
24	(S43) Outgoing Stage 3 BWD R2 signal wait	1,500
25	(S43) Outgoing Stage 3 Initial BWD R2 signal wait	1,500
26	(S45) Outgoing Stage 4 BWD R2 signal wait	1,500
27	(S45) Outgoing Stage 4 Initial BWD R2 signal wait	1,500
28	(S46) Outgoing Host Control wait	24,000
29	(S50) Outgoing Layer 4 Clear wait	400
30	(S49) Outgoing idle line signal wait	12,000
31	(S50) Outgoing idle line signal wait (after glare detected)	12,000
32	(S24) Host Control wait	24,000
33	(S33) Time to wait for Clear Forward after glare detected	1,000
34	Receive line signaling filter	4
35	Not Used	N/A
36	(S6, S24) Incoming BWD R2 Cycle Complete Event wait	400
37	Not Used	N/A
38	(S10) Time to wait for idle line signaling after invalid line signal detected while receiving FWD R2 digits	2,000
39	(S22) Layer 3 Clear Forward wait	300
40	(S39) Outgoing Stage 1 BWD A signal wait after sending all of stage 1 FWD digits	2,000
41	(S2, S3, S4, S5) FWD R2 digit receive wait when String Collection Data field in Inpulsing Parameters Configure is set to 0xFF	144
42	Not Used	N/A
43	R2 Cycle Complete Event wait	200
44	Time to wait for Call Progress Analysis Result	1,500
45	(S43) Time to wait for next BWD R2 signal when stage 3 digits have been outpulsed	2,000