4 E1 Atomic Functions

This chapter documents the atomic functions associated with the E1 PPL component (0x0001) that are released for customization using the PPL Composer.

Atomic Functions

System software version 4.0 or newer is required, unless otherwise noted.

AF Number	51
Name	Set GPR to # of Digits Received in Stage
Description	Sets the value in the GPR indicated by Arg1 to the number of digits received for the stage indicated by Arg2.
Arg1	<GPR #> 1-25
Arg2	<Stage #> 1-4

AF Number	52
Name	Store Received Digit in GPR
Description	Stores a single digit received in the GPR indicated by Arg1. If a digit durations reported, it is stored in the GPR indicated by Arg2.
GPR 2:	Stage # of the received digits
GPR 3:	String # of the received digits
GPR 4:	Digit to store (index into digit buffer)
GPR 5:	Value of the GPR where the digit is to be stored (1-25).
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	53
Name	Store Digits Received in GPR
Description	Stores a single digit received in the GPR indicated by Arg1. If a digit durations reported, it is stored in the GPR indicated by Arg2.
Arg1	<GPR #> 1-25
Arg2	<GPR #> 1-25

AF Number	54
Name	L3PPL Store digit at fwd xmit ctr in General Purpose Register
Description	Sets the GPR indicated by Arg 2 to the digit indexed by the Stage number, as indicated by Arg 1
Arg1	<Stage Number> 1:4
Arg2	<General Purpose Register> 1:25

AF Number	55
Name	L3PPL Store Digit Received in General Purpose Register
Description	Stores a single digit received in the GPR specified by Arg 1
Arg1	<Register Number> 1:25
Arg2	<Not Used>

AF Number	56
Name	L3PPL Store General Purpose Register in Stage at FWD Xmt Dig Ctr
Description	Stores the digit indexed by the forward transmit digit ctr indicated by Arg 1 into the GPR indicated by Arg 2
Arg1	<Stage Number> 1:4
Arg2	<Register Number> 1:25

AF Number	60
Name	Send L4 Out of Service/Blocked
Description	Sends a L3 to L4 Out of Service message with a status of Blocked in order to bring the channel out of service in the call processing layer (L4). This message should be sent when a remote blocked line signaling state is detected.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	61
Name	Send a Busied Out Message to Layer 4
Description	Sends a L3 to L4 Busied Out message after generating local blocked line signaling due to processing a host Busied Out message. This results in updating the call processing layer (L4) for the local busied-out condition.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	62
Name	Send a Q.931 CONNECT Message to Layer 4
Description	Sends a Q.931 CONNECT message to layer 4 for notification that answer has been detected.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	63
Name	Send a DISCONNECT message to Layer 4
Description	Sends a DISCONNECT message to Layer 4 upon the detection of release signaling from the network.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	64
Name	Send a Q.931 CLEAR ACK to Layer 4
Description	Sends a Layer 3 to Layer 4 CLEAR ACK upon detection of idle signaling from the network after release. This will result in Layer 4 sending a Channel Released message to the host, provided that Layer 4 has previously sent an L4 Clear Req PPL event (#58) to the state machine.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	65
Name	Send an In Service Message to Layer 4
Description	Sends a Layer 3 to Layer 4 In Service message.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	66
Name	Send an Out of Service (No Reason) Message to Layer 4
Description	Sends Layer 4 an Out of Service (No Reason) message due to distant end failure to release call.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	67
Name	Send Layer 4 a Call Processing Event message from Call Control Instruction
Description	Sends the host a Call Processing Event message with the event indicated by the current call control instruction and any associated data.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	68
Name	Send Layer 5 a Call Processing Event Message
Description	Sends the host a Call Processing Event message with the event indicated by Arg1 and any associated data.
Arg1	<Call Processing Event> 1–17
Arg2	<Not Used>

AF Number	69
Name	Send a Q.931 SETUP INDICATION to Layer 4 with Address Data
Description	Sends a SETUP INDICATION message to Layer 4 for notification of an incoming call, including any address digits collected to this point. This message will result in Layer 4 sending a Request for Service with Address Data message to the host.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	70
Name	Send a Q.931 SETUP INDICATION to Layer 4
Description	Sends a SETUP INDICATION message to Layer 4 for notification of an incoming call. This message will result in Layer 4 sending a Request for Service message to the host.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	71
Name	Send an Access Denied Message to Layer 4
Description	Sends an ACCESS DENIED message to Layer 4 for notification of an outseize attempt failure, including the failure reason indicated by Arg1 (this should be one of the Outseize Failure message response status).
Arg1	Arg1: <Outseize Failure Status>
Arg2	<Not Used>

AF Number	72
Name	Send a Q.931 ALERTING Message to Layer 4
Description	Sends a Q.931 ALERTING message to Layer 4 for notification of a successful outseizure.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	73
Name	Send Layer 4 a Flash Event Notification
Description	Send Layer 4 a Flash Event Notification. Minimum Software Version: 4.1. Sends a Flash Detected message to L4. To enable host notification, see message "Flash Timing Configure 0x0016" in the API Reference.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	74
Name	L3PPL Send a Setup Indication to Layer 4
Description	Sends a "setup indication" to Layer 4, to report an incoming call with associated address/information signals. The address signaling type is specified by the offset of the Config Byte.
Arg1	<Config Byte Offset> 1 - 200
Arg2

AF Number	77
Name	Send Layer 4 a Call Processing Event/Digits Message
Description	Sends Layer 4 a Call Processing Event/Digits message, including the stages of digits to be reported indicated by Arg1. This will result in Layer 4 sending a Call Processing Event/Digits message to the host.
Arg1	<Stages of Digits to Report>
Arg2	<Not Used>

AF Number	78
Name	Send Call Processing Event /Digits Message
Description	Sends a Call Processing Event /Digits message to the host reporting the digit strings indicated by Arg1.
Arg1	<Stage # Bit Mask> Bit 0 Stage 1 Bit 1 Stage 2 Bit 2 Stage 3 Bit 3 Stage 4
Arg2	<Not Used>

AF Number	79
Name	Send Call Processing Event/Digit With Timing Information Message
Description	Sends a Call Processing Event/Digit With Timing Information message to the host reporting a single digit. If digit duration reporting is not enabled, the duration will be 0.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	80
Name	Send Inseize Control or Outseize Control Response to the Host
Description	Sends an Inseize Control or Outseize Control Response to the host with the error indicated by Arg1. The message sent is determined by which message was originally received.
Arg1	<Response Status> See "API Reference" for values
Arg2	<Not Used>

AF Number	81
Name	Send a Call Processing Event Message with Event ID
Description	Sends a Call Processing Event message with the PPL Event indicated by Arg1.
Arg1	<PPL Event ID>
Arg2	<Not Used>

AF Number	82
Name	Set Receive Stage Status (Minimum Software Version: 4.1)
Description	Updates the receive stage status field for the stage indicated by Arg1 to the value indicated by Arg2.
Arg1	<Stage #> 1 - 4
Arg2	<Value>

AF Number	84
Name	Outpulse BWD R2 Signal in Compelled or Pulsed Mode
Description	Outpulses a BWD R2 signal in either compelled or pulsed mode, depending on the current FWD R2 signaling state. If a FWD R2 signal is present, the BWD R2 signal will be compelled, otherwise it will be pulsed.
Arg1	<BWD R2 Signal> 1 -15 (for both group A and group B).
Arg2	<Value>

AF Number	85
Name	Outpulse BWD R2 Signal in Compelled Mode
Description	Outpulses a BWD R2 signal in compelled mode.
Arg1	<BWD R2 Signal> 1 -15 (for both Group A and Group B).
Arg2	<Not Used>

AF Number	86
Name	Outpulse BWD Pulsed R2 Signal
Description	Outpulses a BWD R2 signal in pulsed mode. The R2 signal value is indicated in Data Byte 2 of a Generate Call Processing Event instruction.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	87
Name	Outpulse BWD Compelled R2 Signal
Description	Outpulses a backward compelled R2 signal. The R2 signal value is indicated in Data Byte 2 of a Generate Call Processing Event instruction.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	88
Name	Outpulse BWD R2 Signal in Compelled Mode/Generate Completion Event
Description	Outpulses a backward R2 signal in compelled mode and instructs the MFDSP card to generate PPL Event 46 (R2 COMP CYCLE COMPLETE) when the R2 cycle is complete (silence is detected in both the forward and backward directions). The R2 signal value is indicated in Data Byte 2 of a Generate Call Processing Event instruction. The PPL must wait in a normal state for this event after executing this atomic function to guarantee that the R2 cycle has completed. Once this event is received, MFC R2 reception/transmission can be cancelled using AF 147.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	89
Name	Outpulse BWD R2 Signal in Compelled Mode/Generate Completion (Using GPR)
Description	Outpulses a backward R2 signal (from GPR indicated by Arg1) in compelled mode and instructs the MFDSP card to generate PPL Event 46 (R2 COMP CYCLE COMPLETE) when the R2 cycle is complete (silence is detected in both the forward and backward directions). The PPL must wait in a normal state for this event after executing this atomic function to guarantee that the R2 cycle has completed. Once this event is received, MFC R2 reception/transmission can be cancelled using AF 147.
Arg1	<GPR #> 1-25
Arg2	<Not Used>

AF Number	90
Name	Outpulse FWD R2 Signal in Compelled Mode
Description	Outpulses a forward R2 signal in compelled mode.
Arg1	<FWD R2 Signal> 1-15 (for both Group I and Group II).
Arg2	<Not Used>

AF Number	91
Name	Outpulse BWD R2 Signal in Compelled or Pulsed Mode
Description	Outpulses a BWD R2 Signal in either compelled or pulsed mode, depending on the current tone receive state. The R2 signal value is indicated in Data Byte 2 of a Generate Call Processing Event message.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	92
Name	Outpulse Next FWD Compelled R2 Signal
Description	Transmits the next FWD compelled R2 signal indicated by the FWD R2 Transmit Digit Counter from the stage indicated by Arg1.
Arg1	<Stage #> 1 - 4
Arg2	<Not Used>

AF Number	93
Name	Outpulse BWD R2 Signal in Forced Pulsed Mode
Description	Outpulses a backward R2 signal in pulsed mode and waits until the R2 signal has been pulsed to process the next atomic function.
Arg1	<BWD R2 Signal> 1-15 (for both Group A and Group B).
Arg2	<Not Used>

AF Number	97
Name	L3PPL Outpulse Single MFR1 Digit
Description	Sends a request to TC to outpulse individual MFR1 digits.
Arg1	<Register Number>
Arg2	<Outp Event Flag>

AF Number	98
Name	Outpulse MFR1 Digits
Description	Sends an internal message to outpulse the MFR1 digit string(s) contained in the Outpulse Stage N Address Data ICB for the stage indicated in Arg1. Note: There must be a least one DSP configured for MFR1 tone transmission for this function to work.
Arg1	<Stage #> 1 - 4
Arg2	<Not Used>

AF Number	99
Name	Outpulse MFR1 Digits for Stage Indicated in Outseize Control Instruction
Description	Sends an internal message to outpulse the MFR1 digit string(s) contained in the Outpulse Stage N Address Data ICB for the stage indicated. Note: There must be at least one DSP configured for MFR1 tone transmission for this function to work.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	100
Name	Outpulse DTMF Digits
Description	Sends an internal message to outpulse the DTMF digit string(s) contained in the Outpulse Stage N Address Data ICB for the stage indicated in Arg1. Note: There must be a least one DSP configured for DTMF tone transmission for this function to work.
Arg1	<Stage #> 1 - 4
Arg2	<Not Used>

AF Number	101
Name	Outpulse DTMF Digits for Stage Indicated in Outseize Control Instruction
Description	Sends an internal message to outpulse the DTMF digit string(s) contained in the Outpulse Stage N Address Data ICB for the stage indicated. Note: There must be a least one DSP configured for DTMF tone transmission for this function to work.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	102
Name	Cancel Outpulsing Digits
Description	Cancels an outstanding outpulse digits request
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	103
Name	Outpulse DTMF Digits
Description	Minimum Software Version: 4.1 Initiates the collection of DTMF digits for the stage indicated by Arg1 using the timer values specified by the Generic Timer ID indicated by Arg2.
Arg1	<Stage #> 1 - 4
Arg2	<Timer ID> 1-100

AF Number	104
Name	Outpulse MFR1 Digits
Description	Minimum Software Version: 4.1 Initiates the collection of MFR1 digits for the stage indicated by Arg1 using the timer values specified by the Generic Timer ID indicated by Arg2.
Arg1	<Stage #> 1 - 4
Arg2	<Timer ID> 1-100

AF Number	105
Name	E1PPL Outpulse MFR1 digits in IFB mode
Description	Sends a request to TC to outpulse MFR1 digits for the stage specified in Arg 1, using IFB mode. No KP/ST Framing
Arg1	<Stage Number> 1:4
Arg2	<Number of Cycles> 1:10

AF Number	106
Name	Outpulse Dial Pulse Digits from Outseize Control Instruction
Description	Sends an internal message to outpulse the Dial Pulse digit string(s) contained in the Outpulse Stage N Address Data ICB for the stage indicated in the ICB. Note: A DSP does not need to be configured for this function to work.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	107
Name	Outpulse Dial Pulse Digits from Outseize Control Instruction for Stage Indicated
Description	Sends an internal message to outpulse the Dial Pulse digit string(s) contained in the Outpulse Stage N Address Data ICB for the stage indicated by Arg1. Note: A DSP does not need to be configured for this function to work.
Arg1	<Stage #> 1 - 4
Arg2	<Not Used>

AF Number	108
Name	Cancel Outpulse Dial Pulse Digits
Description	Cancels an outstanding request for outpulsing Dial Pulse digits.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	109
Name	L3PPL Outpulse DP from fwd xmit ctr in General Purpose Register
Description	Sends a request to xsig to outpulse DP digits for stage specified in Arg 1, beginning at the digit specified by the forward xmit digit ctr.
Arg1	<Stage Number> 1:4
Arg2	<Outp Event Flag> 0:1 0 = No outpulse complete event 1 = Send outpulse complete event

AF Number	112
Name	Generate Tone
Description	Initiates the generation of the tone indicated by Arg1, for the number of cycles indicated by Arg2.
Arg1	<Tone ID> See message "Connect Tone Pattern 0x002F" in the API Reference.
Arg2	<# of Cycles>

AF Number	113
Name	Generate Dialtone
Description	Initiates the transmission of North American Standard Dialtone.
Arg1	<Not Used>.
Arg2	<Not Used>

AF Number	114
Name	Cancel Tone
Description	Cancels the generation of the tone indicated by Arg1.
Arg1	<Not Used>.
Arg2	<Not Used>

AF Number	121
Name	Transmit Line Signaling
Description	Sets the transmit line signaling for a channel. Note: CCITT recommends that the C bit be low (0) and the D bit be high (1).
Arg1	<ABCD Signaling Bits> The ABCD signaling bits are a binary mask representing the line signaling bit combination to be transmitted. The bit order is as follows: Bit # 7 6 5 4 3 2 1 0 Signal Bit A B C D
Arg2	<Not Used>

AF Number	122
Name	Transmit Default Idle Line Signaling
Description	Transmits the preconfigured idle line signaling ABCD bit pattern.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	123
Name	Enable CAS ABCD Bit Line Signaling Scanning
Description	Activates scanning of the Channel Associated Signaling (CAS) ABCD line signaling bits.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	126
Name	E1PPL Attach MFCR2 Reciever (1 - Forward, 2 - Backward) <PPL-CFG-Byte #>
Description	Allocates a MFR2 receiver for Forward/Backward R2 Reception. The first argument determines the direction of the MFR2 signal. The second argument is the location of the configuration byte that contains the setting for the MFR2 tone reception level.
Arg1	MFR2 direction: 1 - Forward, 2 - Backward
Arg2	Index to ppl_cfg_byte which determines if MFR2 tone reception level is set to the high (-22dB) or low (-35dB). The index can be from 1 - 200.

AF Number	127
Name	Setup for FWD Compelled R2 Reception
Description	Allocates a FWD R2 compelled DSP digit receiver. Note: This is a blocking atomic function.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	128
Name	Setup for BWD Compelled R2 Reception
Description	Allocates a BWD R2 compelled DSP digit receiver. Note: This is a blocking atomic function
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	129
Name	Allocate a FWD R2 Digit Buffer for Current Stage
Description	Allocates a forward R2 digit buffer for storing the current stage of address signaling.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	130
Name	Allocate a FWD R2 Digit Buffer
Description	Allocates and initializes a forward R2 signal digit buffer for the stage indicated by Arg1.
Arg1	Stage #> 1 - 4
Arg2	<Not Used>

AF Number	131
Name	Reset FWD R2 Receive Digit Counter for Current Stage
Description	Sets the FWD R2 digit reception counter to 0 for the current address signaling stage.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	132
Name	Reset FWD R2 Receive Digit Counter
Description	Initializes the FWD R2 receive digit counter to 0 for the stage indicated by Arg1.
Arg1	<Stage #> 1 - 4
Arg2	<Not Used>

AF Number	133
Name	Store BWD R2 Signal as Event
Description	Stores the currently received BWD R2 signal for later reporting as a Call Processing Event.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	134
Name	Set BWD R2 Signal Event Bit
Description	Sets the BWD R2 signal event bit used for later reporting as a Call Processing Event.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	135
Name	Test For FWD Receive Digit Counter Value in Range
Description	Minimum Software Version: 4.1. Test atomic function that compares the number of digits collected in Stage 1 to the minimum and maximum number of digits indicated by Arg1 and Arg2 respectively, and returns an Internal PPL Event according to the results.
Arg1	<GPR #> 1-25
Arg2	<GPR #> 1-25

Test Result	PPL Internal Event
< minimum	1
within range	2
> or = to maximum	3

AF Number	136
Name	Clear Stage/FWD Digit Count
Description	Clears the digit string and resets the digit count for the stage indicated by Arg1.
Arg1	<Stage #> 1 - 4
Arg2	<Not Used>

AF Number	139
Name	Send DSP Service Request to Collect Individual Digits/Make Matrix Slave (Addr Sig Type)
Description	Sends a "Request Digits" message to sym to collect individual digits after call setup.
Arg1	<Address Signal Type> 1:2
Arg2	<Not Used>

AF Number	140
Name	Setup for DTMF Reception with Inseize Control Instruction
Description	Allocates a DTMF digit receiver. Digit reception parameters used for controlling digit collection are determined by the inpulsing parameters associated with the stage indicated by the current Receive Stage N Inseize Control instruction. Note: This is a blocking atomic function.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	141
Name	Setup for DTMF Reception
Description	Allocates a DTMF digit receiver. Digit reception parameters used for controlling digit collection are determined by the inpulsing parameters associated with the stage indicated by Arg1.
Arg1	<Stage #> 1 - 4
Arg2	<Not Used>

AF Number	142
Name	Setup for MFR1 Reception with Inseize Control Instruction
Description	Allocates an MFR1 digit receiver. Digit reception parameters used for controlling digit collection are determined by the inpulsing parameters associated with the stage indicated by the current Receive Stage N Inseize Control instruction. Note: This is a blocking atomic function.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	143
Name	Setup for MFR1 Reception
Description	Allocates a MFR1 digit receiver. Digit reception parameters used for controlling digit collection are determined by the inpulsing parameters associated with the stage indicated by Arg1. Note: This is a blocking atomic function.
Arg1	<Stage #> 1 - 4
Arg2	<Not Used>

AF Number	144
Name	Setup for Dial Pulse Reception with Inseize Control Instruction
Description	Allocates a Dial Pulse (DP) digit receiver. Digit reception parameters used for controlling digit collection are determined by the inpulsing parameters associated with the stage indicated by the current Receive Stage N Inseize Control instruction. Note: This is a blocking atomic function.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	145
Name	Setup for Dial Pulse Reception
Description	Allocates a Dial Pulse (DP) digit receiver. Digit reception parameters used for controlling digit collection are determined by the inpulsing parameters associated with the stage indicated by Arg1. Note: This is a blocking atomic function.
Arg1	<Stage #> 1 - 4
Arg2	<Not Used>

AF Number	146
Name	Send DSP Service Request to Collect Individual Digits
Description	Sends a request to collect single digits after call setup and report digit to the host with a Call Processing Event of "Digits". The Address Signaling Type is indicated by Arg1.
Arg1	<Address Signaling Type> 1 = DTMF 2 = MFR1 3= MFR2
Arg2	<Not Used>
Note	The following PPL Configuration Bytes must be configured prior to invoking this function: Bytes 196, 197 Digit Timer (MSB, LSB) = The maximum amount of time to wait for the digit. A value of 0xFFFF disables this timer. Byte 198 0 = disabled, 1 = enabled) Bit 0 = Report the digit at its falling edge (when the first digit is released). If the bit is not set the digit will be reported at its rising edge (when the digit is first pressed). Bit 1 - Ignore "#" character as first digit. Bit 2 = Report digit duration (the amount of time the digit has been pressed). Valid only if configuration bit# 0 is 1. Bytes 199, 200 Minimum Receive Digit Duration Timer (MSB, LSB) = The minimum amount of time for a digit to be present before it is detected and validated.

AF Number	147
Name	Cancel R2 Reception
Description	Releases an MFR2 signal receiver. This function can be used to release R2 receivers used for forward and backward R2 reception.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	148
Name	Collect DTMF Digits
Description	Minimum Software Version: 4.1 Initiates the collection of DTMF digits using the timers defined in the Config Bytes (Arg1) with the values specified by the Generic Timer ID indicated by Arg2.
Arg1	<Config Byte #> 1- 200
Arg2	<Timer ID> 1-100

AF Number	149
Name	Collect MFR1 Digits
Description	Minimum Software Version: 4.1 Initiates the collection of MFR1 digits using the timers defined in the Config Bytes (Arg1) with the values specified by the Generic Timer ID indicated by Arg2.
Arg1	<Config Byte #> 1- 200
Arg2	<Timer ID> 1-100

AF Number	150
Name	Send Request To Do Call Progress Analysis For Class 0 (North American)
Description	Sends an internal message to do Call Progress Analysis for Class 0 (North American). Note: There must be a least one DSP configured for call progress analysis for this function to work.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	151
Name	Test Call Progress Analysis Result and Set up Internal Event
Description	Tests the result of Call Progress Analysis.
Arg1	<Not Used>
Arg2	<Not Used>

Test Result	PPL Internal Event
Answer	80
Error	81
Continuous On	82
Max Silence Timeout	83
Not Determined Timeout	84
Max Determined Timeout	85
Signaling Answer	86
Dialtone	87
Other	0

AF Number	152
Name	Report Call Progress Analysis Result to the Host
Description	Reports the Call Progress Analysis result indicated by Arg1 to the host.
Arg1	<Call Progress Analysis Result>
Arg2	<Not Used>

AF Number	153
Name	Report Call Progress Analysis Result from Atomic Function 151 to the Host
Description	Reports the Call Progress Analysis result from Atomic Function 151 to the host.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	154
Name	Send Request To Do Call Progress Analysis (Class From Arg1)
Description	Sends a request to do Call Progress Analysis for the class indicated by Arg1.
Arg1	<Call Progress Analysis Class>
Arg2	<Not Used>

AF Number	155
Name	Send Request To Do Call Progress Analysis (Class from Outseize Control Message)
Description	Sends a request to do Call Progress Analysis for the class indicated by an Outseize Control message.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	156
Name	Cancel Call Progress Analysis
Description	Sends a request to cancel Call Progress Analysis.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	157
Name	CPC Detection
Description	Initiates CPC detection.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	158
Name	Cancel CPC Detection
Description	Cancels CPC detection.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	159
Name	Reset FWD R2 Transmit Digit Counter to 1
Description	Sets the generate FWD R2 signal counter to 1 for initiation of FWD R2 signal transmission.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	160
Name	Increment FWD R2 Transmit Digit Counter by 1
Description	Increments the generate FWD R2 signal counter by 1.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	161
Name	Decrement FWD R2 Transmit Digit Counter by 1
Description	Decrements the generate FWD R2 signal counter by 1.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	162
Name	Decrement FWD R2 Transmit Digit Counter by 2
Description	Decrements the generate FWD R2 signal counter by 2.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	163
Name	Decrement FWD R2 Transmit Digit Counter by 3
Description	Decrements the generate FWD R2 signal counter by 3.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	164
Name	Test if Current FWD Digit Count > Stage Digit Count
Description	Tests if the current FWD digit count is greater than the stage digit count for the stage number indicated by Arg1.
Arg1:	Arg1: <Stage #> 1 - 4
Arg2:	<Not Used>

Test Result	PPL Internal Event
Greater than	1
Other	0

AF Number	165
Name	Test if Current FWD Digit Count <>== Stage Digit Count
Description	Tests if the current FWD digit count is greater than, less than, or equal to the stage digit count for the stage number indicated by Arg1.
Arg1:	<Stage #> 1 - 4
Arg2:	<Not Used>

Test Result	PPL Internal Event
==	0
<	1
>	2

AF Number	166
Name	Test if FWD Stage Digit Count == 0
Description	Tests if the current FWD digit count for the stage number indicated by Arg1 equals 0.
Arg1:	<Stage #> 1 - 4
Arg2:	<Not Used>

Test Result	PPL Internal Event
== 0	0
Other	1

AF Number	167
Name	Store FWD Transmit Digit Counter Value in GPR
Description	Minimum Software Version: 4.1 Stores the value of the forward digit counter (i.e. number of digits received) for the current call in a GPR.
Arg1:	<GPR #> 1-25
Arg2:	<Not Used>

AF Number	168
Name	Store GPR Value in FWD Transmit Digit Counter
Description	Transfers the contents of a General Purpose register into the forward digit counter for the current call.
Arg1:	<GPR #> 1-25
Arg2:	<Not Used>

AF Number	169
Name	L3PPL Test if Current Xmit Digit Ctr = Stage Digit Count
Description	Checks that the total number of FWD digits to be transmitted is equal to the current FWD transmit digit counter.
Arg1	<Stage Number> 1:25
Arg2	<Not Used>

AF Number	170
Name	Store FWD R2 Signal
Description	Stores the current FWD R2 signal in the digit buffer assigned to the receive digit stage indicated by Arg1. R2 FWD signals are stored in BCD encoded format. The location within the digit buffer where the signal is stored is determined by the current FWD digit counter.
Arg1:	<Stage #> 1 - 4
Arg2:	<Not Used>

AF Number	171
Name	Test If Digit Count == 0xFF
Description	Tests if the digit count for the stage number indicated by Arg1 equals 0xFF.
Arg1:	<Stage #> 1 - 4
Arg2:	<Not Used>

Test Result	PPL Internal Event
== 0xFF)	2
< 0xFF	1
Other	0

AF Number	172
Name	Setup Host Call Processing Event/Digits
Description	Sets up a Call Processing Event/Digits message to send to the host upon collection of a complete stage of digits.
Arg1:	<Stage #> 1 - 4
Arg2:	<Not Used>

AF Number	173
Name	Increment Receive FWD R2 Digit Counter
Description	Increments the current receive stage digit counter due to reception of a FWD R2 signal.
Arg1:	<Stage #> 1 - 4
Arg2:	<Not Used>

AF Number	174
Name	Store L4 Inseize/Outseize ICBsr
Description	Stores Layer 4 Inseize or Outseize Control ICBs for later processing. These ICBs contain inseize or outseize instructions and related data (i.e.: R2 signal to generate). Layer 4 will send Layer 3 an Inseize Control or Outseize Control message after receiving and preprocessing a host Inseize Control or Outseize Control message.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	175
Name	Test for Prior Sending of Layer 3 to Layer 4 SETUP INDICATION
Description	Tests if an L3 to L4 SETUP INDICATION message has been previously sent. Note: A SETUP INDICATION is sent to the Call Processing Layer (L4) to indicate that an incoming call has been received.
Arg1:	<Not Used>
Arg2:	<Not Used>

Test Result	PPL Internal Event
Sent	1
Not Sent	0

AF Number	179
Name	Use Pre-programmed Inseize Instruction List
Description	Points a channel to the inseize instruction list preconfigured on the channel with the Inseize Instruction List Configure message.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	180
Name	Use Instructions in Inseize Control or Outseize Control message
Description	Points a channel to the inseize or outseize instruction list provided by the host through an interactive Inseize Control or Outseize Control message. Note: This function can be used for both inseize and outseize instruction processing.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	181
Name	Reset Instruction Index
Description	Resets the current inseize or outseize instruction pointer to instruction 1. Note: This function can be used for both inseize and outseize instruction processing.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	182
Name	Increment Instruction Index
Description	Increments the current inseize or outseize instruction pointer to the next instruction #. Note: This function can be used for both inseize and outseize instruction #. processing
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	183
Name	Test Current Inseize Control Instruction
Description	Tests for the current Inseize Control instruction
Arg1:	<Not Used>
Arg2:	<Not Used>

Test Result	PPL Internal Event
Null	0
Report Call Processing Event	1
Generate Call Processing Event	2
Receive Stage n Data	3
Wait for Host Control	4
Report Incoming Call	5
Report Incoming Call with Data	6
Generate Inseize ACK	7
Send Host Inseize ACK	8
Use Instruction List	9
Other	20

AF Number	184
Name	Set Call Control Instruction Index to Host Value
Description	Sets the call control instruction index to that indicated in the Use Instruction List ICB sent in an interactive Inseize Control or Outseize Control message by the host.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	185
Name	3
Description	Tests the stage number in the current Inseize Control Instruction. The stage # is determined by the Receive Stage N Address Data Inseize Control instruction currently being processed.
Arg1:	<Not Used>
Arg2:	<Not Used>

Test Result	PPL Internal Event
Stage # 1	1
Stage # 2	2
Stage # 3	3
Stage # 4	4
Other	0xFF

AF Number	186
Name	Test Next Inseize Control Instruction
Description	Tests if the next Inseize Control Instruction is Receive Stage N Address Data.
Arg1:	<Not Used>
Arg2:	<Not Used>

Test Result	PPL Internal Event
Receive Stage N Address Data	1
Other	0

AF Number	187
Name	Test Inseize Control Generate Call Processing Event Instruction
Description	Tests if the next Inseize Control Instruction is Receive Stage N Address Data.
Arg1:	<Not Used>
Arg2:	<Not Used>

Result	PPL Internal Event
ANI Request Off Hook	5
Wink 1	6
Wink 2	7
Wink 3	8
Wink 4	9
Wink 5	10
Wink 6	11
Wink 7	12
Wink 8	13
BWD Pulsed R2 Signal	1
BWD Compelled R2 Signal	2
BWD Compelled R2 Signal with Cycle Completion	3
BWD Compelled or Pulsed R2 Signal	4

AF Number	188
Name	Test Next Inseize Control Instruction for Address Signaling Type
Description	Tests for the receive signaling type from the inpulsing parameters of a stage. The stage number is obtained from the next Inseize Control Instruction, as indicated by the current instruction index (provided that it is a Receive Stage N instruction)..
Arg1:	<Not Used>
Arg2:	<Not Used>

Test Result	PPL Internal Event
DTMF	1
MFR1	2
MFR2	3
Other	20

AF Number	189
Name	Test Address Signaling Type of Stage N Inpulsing Parameters
Description	Tests the inpulsing parameters of the stage indicated by Arg1 for its receive signaling type.
Arg1:	Stage #> 1 - 4
Arg2:	<Not Used>

Test Result	PPL Internal Event
DTMF	1
MFR1	2
MFR2	3
Other	20

AF Number	190
Name	Return Inpulsing Signaling Type
Description	Tests for the receive signaling type from the inpulsing parameters of a stage. The stage number is obtained from the current Inseize Control Instruction, as indicated by the current instruction index (provided that it is a Receive Stage N instruction).
Arg1:	<Not Used>
Arg2:	<Not Used>

Test Result	PPL Internal Event
DTMF	1
MFR1	2
MFR2	3
Other	20

AF Number	194
Name	Test for Outseize Control ICB Buffer
Description	Tests if the Outseize Control ICB buffer is attached to the Layer 4 to Layer 3 CALL REQUEST message.
Arg1:	<Not Used>
Arg2:	<Not Used>

Result	PPL Internal Event
Yes	1
No	0

AF Number	195
Name	Test for Host Outseize Control Instructions
Description	Tests if there are Outseize Control Instructions from the host.
Arg1:	<Not Used>
Arg2:	<Not Used>

Result	PPL Internal Event
Yes	1
No	0

AF Number	196
Name	Use Pre-programmed Outseize Instruction List
Description	Points a channel to use the channel’s pre-programmed outseize instruction list.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	197
Name	Test Current Outseize Control Instruction
Description	Tests for the current Outseize Control instruction.
Arg1:	<Not Used>
Arg2:	<Not Used>

Test Result	PPL Internal Event
Null	0
Scan for Wink	1
Scan for ANI Request Off-hook	2
Scan for Dialtone	3
Report Call Processing Event	4
Outpulse Stage N Digits	5
Wait for Host Address Data	6
Wait for Host Control	7
Send Host Acknowledgment	8
Do Call Progress Analysis	9
Seize	10
Use Pre-programmed Instruction List	11
Cancel R2 Receiver	13
Scan for Backward R2 Signal	14
Wait for Host Control with Answer Supervision	15
Other	20

AF Number	198
Name	Test for Outpulsing Data ICB
Description	Tests if there are host-supplied outpulsing digits for the current stage.
Arg1:	<Not Used>
Arg2:	<Not Used>

Test Result	PPL Internal Event
Yes	1
No	0

AF Number	199
Name	Test Address Signaling Type of Outpulse Stage N Address Data for Current Stage
Description	Tests the address signaling type in the Outpulse Stage N Address Data ICB for the current stage. The stage number is obtained from the current outseize control instruction from list, provided that it is an Outpulse Stage N instruction.
Arg1:	<Not Used>
Arg2:	<Not Used>

Result	PPL Internal Event
DTMF	1
MFR1	2
MFR2	3
MFR1 ALL	4
Dial Pulse	5
Compelled KP	6
Other	20

AF Number	200
Name	Transfer Remaining Digits
Description	Takes digits remaining from the stage indicated by Arg1 and dynamically creates a Data ICB with the remaining address data for the stage indicated by Arg2.
Arg1:	Stage #> 1 - 4
Arg2:	<Stage #> 1 - 4 Note: If a Data ICB already exists for the stage indicated by Arg2, any digits it contains will be over-written by the digits from the stage indicated by Arg1.

AF Number	201
Name	Return Config
Description	Byte # Stores the Config Offset where Outseize Control Instructions end in the GPR indicated by Arg1. The Config Byte indicated by Arg2 indicates where the Outseize Control Instructions begin.
Arg1:	Arg1: <GPR #> 1-25
Arg2:	<Config Byte #> 1- 200

AF Number	202
Name	Test for Outpulsing Data ICB
Description	Minimum Software Version: 4.1. Tests if there are host-supplied outpulsing digits for the current stage
Arg1:	<Stage #> 1 - 4
Arg2:	<Not Used>

Result	PPL Internal Event
No	0
Yes	1

AF Number	203
Name	Test Address Signaling Type of Outpulse Stage N Address Data for Current Stage
Description	Minimum Software Version: 4.1. Tests the address signaling type in the Outpulse Stage N Address Data ICB for the stage indicated by Arg1.
Arg1:	<Stage #> 1 - 4
Arg2:	<Not Used>

Test Result	PPL Internal Event
DTMF	1
MFR1	2
MFR2	3
MFR1 ALL	4
Dial Pulse	5
Compelled KP	6
Other	20

AF Number	204
Name	Store Digit Collection Status
Description	Stores the digit collection status for the stage indicated in the current Receive Stage N Address Data inseize control instruction.
Arg1:	<Status #> 66 - Digits Received 67 - First Digit Timeout 68 - Inter-digit Timeout 69 - Digits Complete Timeout
Arg2:	<Not Used>

AF Number	205
Name	Store Digits
Description	Stores a DSP decoded digit string in the inpulsing stage digit buffer associated with the stage indicated in the current Receive Stage N Address Data inseize control instruction data.
Arg1:	<Not Used>
Arg2:	<Not Used>

AF Number	206
Name	Store Digits
Description	Stores a DSP decoded digit string in the inpulsing stage digit buffer associated with the stage indicated by Arg1.
Arg1:	<Stage #> 1 - 4
Arg2:	<Not Used>

AF Number	207
Name	Update Timeout Status
Description	Minimum Software Version: 4.1 Updates the Receive digit status for the stage indicated by Arg2 according to the test results shown below. The status is reported in the Request for Service with Data message.
Arg1:	<Timeout Value>
Arg2:	<Stage #> 1 - 4

Test Result	Status
Digits Received	0x10 (Positive ACK)
First Digit Timeout	0x81(Permanent Signal Condition
Interdigit Timeout	0x80 (Partial Dial Condition)
Digits Complete Timeout	0x92 (Inpulsing Complete Timeout)

AF Number	208
Name	Store Single Digit in Stage
Description	Minimum Software Version: 4.1 Stores a single digit in the Receive Stage digit buffer for the stage indicated by Arg1. PPL Event 66 (DSP Result Digits) must be the event received immediately preceding this AF.
Arg1:	<Stage #> 1 - 4
Arg2:	<Not Used>