L3P BT IUP (0x0011)

You are here: PPL Developer’s Guide > 6 SS7 Atomic Functions > L3P BT IUP (0x0011)

L3P BT IUP (0x0011)

This section documents the atomic functions associated with L3P BT IUP.

AF Number	160
Name	Send L3 an equip circuit request.
Description	This function will send an equip message to L3 (i.e. iupcpc).
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	Message is queued for L3
Returns	Success always

AF Number	161
Name	Out of Service atomic function to restore the In-Service Protocol
Description	This function will restore the Primitive table and Event tables to point to the In-Service protocol, and the Protocol ID to the In-Service Protocol ID. The function exits with a status allowing the calling function, in message preprocessor file, to force the In-Service protocol to the desired state.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	See Description.
Returns	PPLerrSET_SM_STATE

AF Number	162
Name	Out of Service atomic function to restore the In-Service Protocol
Description	This function will check for congestion in the outbound direction.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	PPLevINT_EVENT_1 if Output Congestion is detected; PPLevINT_EVENT_0 otherwise
Returns	Success always

AF Number	170
Name	Validate L4/L5 Message
Description	This function will validate any message which originates from L4 or L5. Messages which contain IUP ICBs are validated and completed using the default information contained in the configuration byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	The internal "down working" buffer will contain a valid TLV formatted message, if Success is returned. The PPLevINT_EVENT_1 is set if successful, otherwise PPLevINT_EVENT_0 is returned.
Returns	Success always

AF Number	171
Name	Send PPL Event Indication SSM to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	172
Name	Send PPL Event Indication SER to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	173
Name	Send PPL Event Indication ECM to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	174
Name	Send PPL Event Indication CFC to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	175
Name	Send PPL Event Indication OOR to L5
Arg1	<Not Used>
Arg2	<Not Used><Not Used>
Returns	Success always

AF Number	176
Name	Send PPL Event Indication HLR to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	177
Name	Send PPL Event Indication SIM to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	178
Name	Send REL with Reason in REG to L3
Arg1	Register number containing the Release Reason
Arg2	<Not Used>
Returns	Success always

AF Number	179
Name	Send CAN with Reason in REG to L3
Arg1	Register number containing the Release Reason
Arg2	<Not Used>
Returns	Success always

AF Number	180
Name	Set Timer associated value
Description	Associates a value with one of the three timers. Later when the timer expires the value may be retrieved to determine the current usage of the timer and take the appropriate action.
Arg1	Timer number Range 1 thru 3
Arg2	Associated value
Returns	Success always

AF Number	181
Name	Get Timer associated value
Description	Retrieves the associated value
Arg1	Timer number
Arg2	Register to contain associated value
Returns	Success always

AF Number	182
Name	Send PPL Event Indication CLR to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	183
Name	Send PPL Event Indication RE-ANSWER (RAN) to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	184
Name	Send PPL Event Indication SUS to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	185
Name	Send PPL Event Indication RES to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	186
Name	Send PPL Event Indication SWAP to L5
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	187
Name	Send Block Upon Release Event to L3
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	200
Name	Send IAM to L3
Description	This function will send the IAM message to L3. The IAM message is either taken from the "down working" buffer or if the down working buffer is empty, the IAM is taken from the Configuration Byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Returns	Success always

AF Number	201
Name	Send IFAM to L3
Description	This function will send the IFAM message to L3. The IFAM message is either taken from the "down working" buffer or if the down working buffer is empty, the IFAM is taken from the Configuration Byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	202
Name	Send FAM to L3
Description	This function will send the FAM message to L3. The FAM message is either taken from the "down working" buffer or if the down working buffer is empty, the FAM is taken from the Configuration Byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	203
Name	Send SAM to L3
Description	This function will send the SAM message to L3. The SAM message is either taken from the "down working" buffer or if the down working buffer is empty, the SAM is taken from the Configuration Byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	204
Name	Send REL to L3
Description	This function will send the REL message to L3. The REL message is either taken from the "down working" buffer or if the down working buffer is empty, the REL is taken from the Configuration Byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	205
Name	Copy up working buffer to save buffer.
Description	This function will free the save buffer, if required. Allocate a new save buffer and copy the up working buffer into the save buffer.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	206
Name	Append up working buffers’ TLVs onto save buffer.
Description	This function will check to see that a save buffer has been allocated. (If not, this function will cause a channel purge.) Copy any TLVs in the up working buffer to the save buffer.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success or PPLerrAF_INITIATED_PURGE

AF Number	207
Name	Swap up working buffer ptr with save buffer ptr
Description	This function will just sway the up working buffer ptr with the save buffer ptr.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	208
Name	Send SND to L3
Description	This function will send the SND message to L3. The SND message is either taken from the "down working" buffer or if the down working buffer is empty, the SND is taken from the Configuration Byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	209
Name	Send CNA with Reason to L3
Description	This function will send a copy of the CNA message stored in the config byte area to L3. Arg1 is used to specify the reason value.
Arg1	Reason
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	210
Name	Send ACM to L3
Description	This function will send the ACM message to L3. The ACM message is either taken from the "down working" buffer or if the down working buffer is empty, the ACM is taken from the Configuration Byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	211
Name	Send ACI to L3. The "down working " buffer must be contain the ACI message to be sent.
Description	This function will send the ACI message to L3
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success if the down working buffer contains a message. Otherwise, the channel will be purged.

AF Number	212
Name	Send REL with Reason to L3
Description	This function will send the REL message to L3 with Arg1 containing the reason.
Arg1	Reason
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	213
Name	Send ANS to L3
Description	This function will send the ANS message to L3. The ANS message is either taken from the "down working" buffer or if the down working buffer is empty, the ANS is taken from the Configuration Byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	214
Name	Send UNDEFINED message to L3
Description	This function will send the a message contained in the Generic TLV Entry Data or a message beginning with a unknown H0,H1 value within the H0,H1 Element TLV to L3.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success if the down working buffer contains a message. Otherwise, the channel will be purged.

AF Number	215
Name	Send ACI to L3 of user defined type
Description	This function will send the specified ACI type message from the config byte area to L3.
Arg1	Desired ACI message type. Range 1 through 7
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success if a valid ACI message type is specified. Otherwise, the channel will be purged.

AF Number	216
Name	Load requested ACI info from Config Bytes.
Description	This function will send the requested ACI type message from the config byte area to L3. The requested info is expected in an ACI type 7 message contained in the up working buffer. Supported ACI Information Request Codes are 1 through 9 , 11, and 12.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	PPLevINT_EVENT_1 if the ACI message is a type 7 Information Request. Otherwise, it will return PPLevINT_EVENT_0.
Returns	Success if a valid ACI message type is specified. Otherwise, the channel will be purged.

AF Number	217
Name	Copy L3 message into Up Working Buffer
Description	This function will copy an incoming message form L3 into the up working buffer for use by L3P and possibly higher layers.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	218
Name	Send BLO to L3
Description	This function will send a Block message to L3. . The BLO message is either taken from the "down working" buffer or if the down working buffer is empty, the BLO is taken from the Configuration Byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	219
Name	Send UBL to L3
Description	This function will send a Unblock message to L3. The UBL message is either taken from the "down working" buffer or if the down working buffer is empty, the UBL is taken from the Configuration Byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	220
Name	Send an ACI type 7 Request message to L3 with user defined IRC type
Description	This function will send an ACI type 7 message to L3 with the Information Request Code specified in Arg1.
Arg1	The Information Request Code. Range 1 through 12 Except 3, 4, 10.
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success if Arg 1 is valid. Otherwise, the channel is purged.

AF Number	221
Name	Send PPL Event Indication to the Host with event specified in the register.
Description	This function will send a PPL Event Indication to the Host. Arg1 specifies the register containing the event.
Arg1	The Register number which contains the event to be reported.
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	222
Name	Set OOS op Flag to the user specified value
Description	This function will set the Out Of Service operation flag.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	223
Name	L3PIUP Take CIC OOS
Description	This function will Cause an L3P reset to occur.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	With a status of PPLerrAF_INITIATED_RESET

AF Number	224
Name	L3PIUP Test OOS OP Flag
Description	This function will setup a PPL internal event corresponding to the value of the Operation Flag.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	With a status of PPLevINT_EVENT_0 + the value of the Operation Flag

AF Number	225
Name	L3PIUP Send Unequip message to L3
Description	This function will send an unequip message to L3
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	226
Name	L3PIUP Generated In-Service event
Description	This function will send a Transition to In-Service message to L3P.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	227
Name	Send A CFN Event to L3
Description	This function will send a CFN event to L3.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	229
Name	Send A PPL Event Indication of ANS received before ACM to L5
Description	This function will send the above PPL Event Indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	230
Name	Send Access Denied to L4
Description	This function will send the Access Denied message to L4.
Arg1	Reason for denying access
Arg2	Call Status 0=Call Inactive, 1=Call Active
Outputs	<Not Used>
Returns	Success always

AF Number	231
Name	Send PPL Event Indication to L5 if enabled by the corresponding Config Byte.
Description	This function will send a PPL Event Indication to L5 if the corresponding Config byte has been enabled to allow a PPL Event Indication to be issued.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success and PPLevINT_EVENT_1 PPL Event Indication was sent. Otherwise, it is a PPLevINT_EVENT_0.

AF Number	232
Name	Test if IUP ICB is Present
Description	This function will test to see if an IUP ICB is present in the message.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success and a PPLevINT_EVENT_1. Otherwise, it is a PPLevINT_EVENT_0.

AF Number	233
Name	Test if Stage N Address Data ICB is present
Description	This function will test to see if a Stage N Address Data ICB is present in the message.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success and a PPLevINT_EVENT_1. Otherwise, it is a PPLevINT_EVENT_0.

AF Number	234
Name	Send Cut Through to L4
Description	This function will send a Cut Through message to L4.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	235
Name	Send Connect to L4
Description	This function will send a Connect message to L4.
Arg1	<Not Used>
Arg2	<Not Used><Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	236
Name	Send Disconnect to L4
Description	This function will send a Disconnect message to L4.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	237
Name	Send Clear Request to L4
Description	This function will send a Clear Request message to L4.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	238
Name	Test and Get Call Type ICB
Description	This function will test to see if a Call Type ICB is present in the message and if so, get the call type byte.
Arg1	Register number to contain the Call Type byte if one is present
Arg2	<Not Used>
Outputs	PPLevINT_EVENT_0 = No Call Type byte present, PPLevINT_EVENT_1 = Call Type byte is present.
Returns	Success always

AF Number	239
Name	Setup Multi Purpose Timer 18 based upon No. Digits Requested and the Exchange Type.
Description	This function will setup the timeout value for timer 18 to a value based upon the number of digits required (in the register specified by Arg1) and the Exchange Type (in the register specified by Arg2).
Arg1	A register containing the number of digits requested in a SND message
Arg2	A register containing the Exchange Type. 0 = Terminating, 1 = Intermediate
Outputs	<Not Used>
Returns	Success if valid input arguments. Otherwise, the channel is purged.

AF Number	240
Name	Test and Get ptr to TLV in specified buffer
Description	This function will examine the up or down working buffer to see if the IUP ICB contains the requested TLV.
Arg1	The requested TLV ID
Arg2	The buffer to check 0 = Upworking Buffer, 1 = Downworking Buffer
Outputs	PPLevINT_EVENT_1 if the TLV is located and an internal variable is setup pointing to the located TLV. Otherwise, PPLevINT_EVENT_0 is returned.
Returns	Success always

AF Number	241
Name	Test and Get TLV byte into register
Description	This function will get the specified byte from the working buffer containing a TLV of interest, and copy it into the specified register.
Arg1	The number of the byte to fetch (Range 1 to 256), Beginning with the first data byte.
Arg2	The number of the register to contain the requested byte
Outputs	If successful PPLevINT_EVENT_1 is returned, Otherwise, the specified register is cleared and PPLevINT_EVENT_0 is returned.
Returns	Success always

AF Number	242
Name	Get Config byte into GPR 10
Description	This function will get the specified configuration byte into General Purpose Register 10. The user specifies the configuration byte by Block number and Byte number.
Arg1	The Block number containing the byte. (Range 1 to 3)
Arg2	The offset to the desired byte. (Range 1 to 200)
Outputs	If successful PPLevINT_EVENT_1, otherwise PPLevINT_EVENT_0 is returned.
Returns	Success always

AF Number	243
Name	Arg1:GPR = Arg1:GPR – Arg2:GPR
Description	This function will subtract the contents of the register specified in Arg2 from the contents of the register specified in Arg1. The results are stored in register specified in Arg1.
Arg1	Any GPR
Arg2	Any GPR
Outputs	PPLevINT_EVENT_0 if the resulting contents of GPR specified in Arg1 is < 0 (i.e Arg2 > Arg1) PPLevINT_EVENT_1 if the resulting contents of GPR specified in Arg1 is > 0 (i.e. Arg1 > Arg2) PPLevINT_EVENT_2 if the resulting contents of GPR specified in Arg1 is 0 (i.e. Arg1 = Arg2)
Returns	Success always

AF Number	244
Name	Form SND message using GPR value for N
Description	This message will format a SND message in TLV format using the contents of the register specified in Arg1 as the N value. (i.e. the number of digits requested). The SND message is either taken from the "down working" buffer or if the down working buffer is empty, the SND is taken from the Configuration Byte area.
Arg1	The number of a register containing the number of digits requested.
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	245
Name	Append accumulated addressed digits into Up Working buffer.
Description	This function will insert the original IAM message into the upworking buffer with the total accumulated address signals from the original IAM and subsequent SAM or FAM message.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success, If a previous IAM was not received the channel is purged.

AF Number	246
Name	Arg1:GPR = Arg1:GPR + Arg2:GPR
Description	This function will add the contents of the register specified in Arg2 to the contents of the register specified in Arg1. The results are stored in register specified in Arg1.
Arg1	Any GPR
Arg2	Any GPR
Outputs	<Not Used>
Returns	Success always

AF Number	247
Name	Save Address Digits
Description	This function will save the received address digits (form a IAM or IFAM) into an internal buffer. The contents of the internal buffer are overwritten with the new address digits.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	248
Name	Append Address Digits
Description	This function will append the digits received from a SAM or FAM to internal buffer containing previously saved address digits.
Arg1	The number of a General Purpose Register to contain the total number of address digits collected for this call.
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success, Otherwise, PPLerrAF_INITIATED_PURGE if no digits were previously saved.

AF Number	249
Name	Form ICB Setup message for L4
Description	This function will form a setup message for L4 in ICB format.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success or PPLerrAF_INITIATED_PURGE if up working buffer is not valid.

AF Number	250
Name	Form BCD Setup message for L4
Description	This function will form a setup message for L4 in BCD format.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success or PPLerrAF_INITIATED_PURGE if up working buffer is not valid.

AF Number	251
Name	Send Formatted Setup message to L4
Description	This function will send the formatted message created by (Form ICB Setup message for L4 or Form BCD Setup message for L4) and send it to L4.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	252
Name	Send PPL Event Indication ACI to L5
Description	This function will send a PPL Event Indication of ACI to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	253
Name	Send PPL Event Indication SAM to L5
Description	This function will send a PPL Event Indication of SAM to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	254
Name	Send PPL Event Indication FAM to L5
Description	This function will send a PPL Event Indication of FAM to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	255
Name	Send NACK or ACK to L5
Description	This function will send a ACK or NACK to L5 based upon the contents of Arg1.
Arg1	0 = NACK, 1 = ACK
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	256
Name	L3PIUP Send Response to Outseize Control Message
Description	This function will send an response to L5 with a status specified in Arg1.
Arg1	The value to be sent in the status field of the message
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	257
Name	Send PPL Event Indication UNDEFINED Msg to L5
Description	This function will send a PPL Event Indication of UNDEFINED message to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	258
Name	Send PPL Event Indication Circuit already Blocked to L5
Description	This function will send a PPL Event Indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	259
Name	Send PPL Event Indication Call Connected to L5
Description	This function will send a PPL Event Indication of Call Connected to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	260
Name	Send PPL Event Indication SND to L5
Description	This function will send a PPL Event Indication of SND to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	261
Name	Form IFAM from Stage N Address Data ICB
Description	This function will format an IFAM TLV message from a Stage N Address Data ICB message.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	If successful PPLevINT_EVENT_1 is returned, otherwise PPLevINT_EVENT_0.
Returns	Success or Failure

AF Number	262
Name	Send PPL Event Indication of Circuit NOT Blocked to L5
Description	This function will format a PPL Event Indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	263
Name	Send PPL Event Indication of Error Timer Expired, Sending CNA to L5
Description	This function will format a PPL Event Indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	264
Name	Send PPL Event Indication to host
Description	This function will format a PPL Event Indication message using the Arg1 value as the event, and send it to the host.
Arg1	The event.
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	265
Name	PURGE CHANNEL
Description	This function will cause the Channel to be Purged, with the reason specified in Arg1.
Arg1	The purge reason
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	266
Name	Send PPL Event Indication CFN to L5
Description	This function will send a PPL Event Indication of CFN to L5. In addition if a buffer is present in the m_message it will be sent also.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	267
Name	Send PPL Event Indication No Response to ACI Request to L5
Description	This function will send a PPL event Indication to the L5 when timer 2 (i.e. TO-14) expires due to not receiving any ACI response from an ACI request.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	268
Name	Send PPL Event Indication of CNG to L5
Description	This function will send this indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	269
Name	Send PPL Event Indication of CNA to L5
Description	This function will send this indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	270
Name	Send PPL Event Indication of RAM to L5
Description	This function will send this indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	271
Name	Send PPL Event Indication of SEM to L5
Description	This function will send this indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	272
Name	Send PPL Event Indication of SAD to L5
Description	This function will send this indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	273
Name	Send PPL Event Indication of SASUI to L5
Description	This function will send this indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	274
Name	Send PPL Event Indication of ASUI to L4
Description	This function will send this indication to L5.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	275
Name	Send PPL Event Indication of No response to SASUI request
Description	This function will send a PPL Event Indication to the L5 when Timer 2 (i.e. TO-14) expires due to not receiving any ASUI response from an SASUI request.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	276
Name	Load Requested ASUI info from Config Bytes
Description	This function will form the appropriate ASUI message into the down working buffer based upon the SASUI request in the up working buffer. The ASUI message is taken from the Config byte area.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	If it is a valid request PPLevINT_EVENT_1, otherwise PPLevINT_EVENT_0.
Returns	Success always

AF Number	277
Name	Send ASUI to L3
Description	This function will send an ASUI message to L3.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	278
Name	Send SASUI to L3
Description	This function will send a SASUI message to L3.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	279
Name	Send SASUI request message to L3, with user defined type
Description	This function will send a SASUI message to L3, of the type specified in Arg1.
Arg1	The Type of ASUI message to be returned (range 0 to 255). Only 1 is currently valid.
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	280
Name	Force sending an ACM message to L3
Description	This function will dynamically build and send an ACM message to L3. The contents of the down working buffer are not accessed or disturbed.
Arg1
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	281
Name	Set Remote Maintenance Blocking State
Description	This function will allow the user to set the Remote Maintenance Blocking state.
Input Argument 1	0 = Unblocked, 1 = Blocked
Input Argument 2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	282
Name	Set Local Maintenance Blocking State
Description	This function will allow the user to set the Local Maintenance Blocking state.
Input Argument 1	0 = Unblocked, 1 = Blocked
Input Argument 2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	283
Name	Test Blocking State
Description	This function will allow the user to Test any of the following local or remote blocking states. Maintenance, Hardware, and Software.
Input Argument 1	Blocking Location. 0 = Local, 1 = Remote
Input Argument 2	Blocking Type. 0 = Maintenance, 1 = Hardware, 2 = Software.
Outputs	If blocked PPLevINT_EVENT_1 is returned, otherwise PPLevINT_EVENT_0.
Returns	Success always

AF Number	284
Name	Send SAD to L3
Description	This function will send a SAD message to L3.
Input Argument 1	<Not Used>
Input Argument 2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	285
Name	Test Accumulated Digits against Config Byte Digits
Description	This function compares n digits of the accumulated digits string with the digit string contained in the config byte area, at the specified config block and byte number. If the config byte string contains a digit of F that digit is skipped, in the config byte area and the accumulated digit string area. NOTE: The digit to begin comparison, within the accumulated digit string is set by the value in register 20.
Arg1	The Config byte block number. Range 1 through 3
Arg2	The byte number within the above block. Range 1 through 200
Outputs	PPLevINT_EVENT_0 if match fails. Or the config bytes exceed the size block limit. PPLevINT_EVENT_1 if match succeeds
Returns	Success always

AF Number	286
Name	Test Accumulated Digits against Immediate Value
Description	This function compares from 1 to 4 digits of the accumulated digits string with the digit string contained in Arg2. If a nibble within Arg2 contains an F that digit is skipped. NOTE: The starting digit within the accumulated digit string is set by the value in register 20.
Arg1	The number of bytes present in Arg2 to check. (range 1 to 4)
Arg2	The digits to validate against the accumulated buffer. NOTE: A value of 0x4321 would attempt to match a 1 against the first digit in the accumulated digit string, a 2 against the second digit, a 3 against the third...
Outputs	PPLevINT_EVENT_0 if match fails. Or the config bytes exceed the size block limit. PPLevINT_EVENT_1 if match succeeds
Returns	Success always

AF Number	287
Name	Send Alarm Msg to Host
Description	This function will send an ALARM message to the Host using the user defined Severity, Entity, and Alarm values. Please refer to ALARM.H for normal values for these elements.
Arg1	High byte Severity, Low byte Entity
Arg2	Alarm Value
Outputs	Alarm message is sent to L5
Returns	Success always

AF Number	288
Name	Set OOS Reason
Description	This function will Set the Out Of Service Reason to the value specified in Arg1.
Arg1	OOS reason.
Arg2	<Not Used>
Outputs	...rw->unique_to.l3p_tup.oos_reason = Arg1
Returns	Success always

AF Number	289
Name	Send Purge Message to L4
Description	Just sends the Purge Message to L4.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always

AF Number	290
Name	Clear Up Working Buffer Ptr
Description	This function will free the buffer attached to the up_working_buffer_ptr, if present.
Arg1	<Not Used>
Arg2	<Not Used>
Outputs	up_working_buff_ptr is set to NULL.
Returns	Success always

AF Number	291
Name	Set the In-Service_startup_flag to value in Arg1.
Description	This function will set the read write variable "inservice_startup_flag" to the value suPPLied in Arg1.
Arg1	Value.
Arg2	<Not Used>
Outputs	...inservice_startup_flag = value.
Returns	Success always

AF Number	292
Name	Get the In-Service_startup_flag value into register
Description	This function will load the contents of In-Service_startup_flag variable into the register specified in Arg1.
Arg1	Register to contain the value of inservice_startup_flag.
Arg2	<Not Used>
Outputs	<Not Used>
Returns	Success always