L3P CIC (0x000F)

You are here: PPL Developer’s Guide > 6 SS7 Atomic Functions > L3P CIC (0x000F)

L3P CIC (0x000F)

This section documents the atomic functions associated with L3P CIC.

Atomic Functions

The following AFs are specific to the L3P CIC Call Control PPL component.

AF Number	51
Name	Send L4 Channel Status In Service
Description	Sends L4 a channel in service indication.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	52
Name	Send ISUP Circuit Reset
Description	Sends ISUP a CIC reset request using no parameters.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	53
Name	Fault
Description	Generates an SS7 card fault using fault code in Arg1.
Arg1	<Fault Code>
Arg2	<Not Used>

AF Number	54
Name	PPL Restore Channel’s Assigned Protocol
Description	Function to switch from the OOS to the INS protocol.
Arg1	<Fault Code>
Arg2	<Not Used>

AF Number	55
Name	PPL Send L5 PPL Event Indication using L4/L5 Outgoing Buffer
Description	Sends a PPL Event Indication to the host using the event ID in Arg1 and sending up any ISUP parameters stored in the L4/L5 outgoing buffer.
Arg1	<Event ID>
Arg2	<Not Used>

AF Number	56
Name	Send L4 a Cut Through
Description	Sends L4 a cut through indication.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	57
Name	Send L5 PPL Event
Description	Sends a PPL event indication to the host using the Event ID in Arg1 and sending up ICB with the data in Arg2.
Arg1	<Event ID>
Arg2	<Event Data>

AF Number	58
Name	Send ISUP OOS Maintenance Loopback Ack
Description	Notifies ISUP that the requested PCM loopback has been established.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	59
Name	Copy Default ISUP Parameters into L5 Incoming Buffer
Description	Loads the PPL Config Byte prestored parameters at offset in Arg1 into the L5 incoming buffer.
Arg1	<Config Byte Offset of Defaults>
Arg2	<Not Used>

AF Number	61
Name	Test for Existence of BCD Encoded Digits in Message
Description	Tests an Outseize Control message for the existence of BCD digits.
Arg1	<Not Used>
Arg2	<Not Used>

Test Result	PPL Internal Event
Digits not present	0
Digits present	1

AF Number	62
Name	Send L4 a Q.931 Connect Message
Description	Sends L4 a Connect Indication.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	63
Name	Send L4 a Q.931 Disconnect
Description	Sends L4 a disconnect Indication.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	64
Name	Send L4 a Q.931 Clear using L4/L5 Outgoing Buffer
Description	Sends L4 a Clear indication including any parameters present in the L4/L5 outgoing buffer.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	65
Name	Send L4 OOS Maintenance Loopback
Description	Send L4 an OOS indication which also requests that a PCM loopback be connected to the channel.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	66
Name	Send L4 an Out of Service Message
Description	Sends an Out of Service message to L3/L4 with the reason indicated by Arg1.
Arg1	<Reason>
Arg2	<Not Used>

AF Number	67
Name	Test L5 Incoming Buffer for parameters and assemble with defaults
Description	Search the L4/L5 incoming buffer for an ICB relating to the message configuration specified in Arg1. If found, the ICB is concatenated with prestored parameters in the Config Bytes at the index specified by Arg2 and the resulting ICB is placed into the L4 /L5 incoming buffer.
Arg1	<ISUP Message Config Index>
Arg2	<Config Byte with Default>

Test Result	PPL Internal Event
No ICB Found	0
ICB Found	1

AF Number	68
Name	Copy Default ISUP Parameters and use BCD-Encoded digits into L5 Incoming Buffer
Description	Searches for a Stage N Address Data ICB w/ BCD encoded digit strings in the L4/L5 incoming buffer. The digits are translated into SS7 Called and Calling Party Number parameters using the parameter IDs specified in the MSB (Called Party) and LSB (Calling Party) of Arg2. The parameters are concatenated with prestored parameters in the config bytes at the index specified in Arg1. The resulting ICB is stored in the L4/L5 incoming buffer.
Arg1	<Config Byte Offset Of Defaults> 1-200
Arg2	<Called Number Party ID/Calling Number Party ID>

AF Number	69
Name	Send L4 a Q.931 SETUP using L4/L5 Outgoing Buffer
Description	Sends L4 a call SETUP indication including any SS7 parameters present in the L4/L5 outgoing buffer.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	71
Name	Transfer L5 Formatted Raw SS7 Parameters from L4/L5 Incoming to ISUP Outgoing Buffer
Description	Searches the L4/L5 incoming buffer for the ICB corresponding to the message configuration specified by Arg1. Once found, the ICB is transferred to the ISUP outgoing buffer.
Arg1	<ISUP Message Config Index>
Arg2	<Not Used>

AF Number	72
Name	Send L4 a Q.931 Alerting
Description	Sends L4 an alerting indication including any parameters present in the L4/L5 outgoing buffer.
Arg1	<Not Used>
Arg2	<Not Used>

AF Number	73
Name	Test for Existence of SS7 Parameters in Message
Description	Test any message for the presence of SS7 ICB buffers.
Arg1	<Not Used>
Arg2	<Not Used>

Test Result	PPL Internal Event
No parameters present	0
Parameters present	1

AF Number	74
Name	Purge Channel
Description	Initiates a channel purge with purge reason specified in Arg1.
Arg1	<Purge Code>
Arg2	<Not Used>