X.25 Development Tools Error Messages

This section contains descriptions of the errors generated in the X.25 Development Tools and lists the codes associated with those errors.

X.25 Development Tools Error Codes

The following is a table of all X.25 generated error codes:

X.25 Error Messages
Description	Error	Hex Code
Library not initialized	EX25NOINIT	0x100
Library error	EX25LIB	0x101
No more memory available	EX25MALLOC	0x102
Bad DTE address	EX25DTEADDR	0x103
Interrupted operation	EX25INTR	0x104
Buffer in use	EX25BUFUSED	0x105
Connection not established	EX25NOCONN	0x106
Bad facility length	EX25FACLEN	0x107
Done command timed-out	EX25DONETO	0x108
Invalid connection number	EX25ICONN	0x109
No pending request	EX25NOPEND	0x10A
Invalid tools initialization	EX25INVINIT	0x10B
Invalid gateway name	EX25ISRVNAME	0x10C
Invalid NULL pointer address	EX25NULLPTR	0x10D
Invalid option	EX25INVOPT	0x10E

Network Error Messages

Network Error Constants
Description	Constant	Hex Code
Maximum error message length	ENETMSGLEN	0x130
Maximum ENET error number	ENETMAX	0xFF

Network Error Messages
Description	Error	Hex Code
Invalid buffer length	ENETBUFLEN	0x01
Invalid command	ENETICMD	0x03
Command timeout	ENETCMDTO	0x05
Incomplete message	ENETIMSG	0x06
Invalid local session number	ENETILSN	0x08
No circuit available	ENETNOCKT	0x09
Call cleared	ENETCALLCLR	0x0A
Command cancelled	ENETCMDCANC	0x0B
PU name exist	ENETPUEXIST	0x0D
PU name table full	ENETPUFULL	0x0E
Session table full	ENETNOSESS	0x11
Unsuccessful call	ENETUCALL	0x12
Protocol name not found	ENETNAMENF	0x14
Circuit in use	ENETINUSE	0x16
PU name not found	ENETNOPU	0x17
Session reset	ENETSRESET	0x18
Trace not started	ENETNOTRACE	0x19
Insufficient memory	ENETNOMEM	0x1A
Too many outstanding commands	ENET2MANYC	0x22
Bad port number	ENETBADPORT	0x23
No number to dial	ENETNONUMBER	0x25
No dial tone	ENETNOTONE	0x40
Modem test failed	ENETMDFAILED	0x50
Modem not ready	ENETMDNR	0x90
Modem not ready (no DSR)	ENETMDDSR	0x91
Modem not ready (no CTS)	ENETMDCTS	0x92
Modem not ready (no clock)	ENETMDCLK	0x93
Remote line busy	ENETBUSY	0x94
Remote not answering	ENETNOIANSWER	0x95
No line available	ENETNOLINE	0x96
Modem in use	ENETMDUSED	0x99
Bad phone number syntax	ENETMDSYNTAX	0x9E
Modem initialized	ENETMDINIT	0x9F
Link level not ready	ENETLINKNR	0xA0
Packet level not ready	ENETPKTLNR	0xB0
Restart indication received	ENETRESTART	0xB2
Transport connection cleared remotely	ENETXPTCCLRR	0xC0
Transport connection cleared locally	ENETXPTCCLRL	0xC1
Timeout occurred on CR or DR	ENETXPTOUTCRDR	0xC2
X.25 network connection cleared	ENETXPXNETCLR	0xC3
X.25 network reset	ENETXPXNETRESET	0xC4
Transport connection refused by remote	ENETXPTCREFR	0xC5
CR sent by remote site not acceptable	ENETXPCRRNA	0xC6
Not enough memory to start transport layer	ENETXPNOMEM	0xCF
Submit request again	ENETAGAIN	0xF8
Eiconcard snapshot	ENETSNAP	0xF9
Eiconcard snarked	ENETSNARK	0xFA
Eiconcard error	ENETCARD	0xFB
Eiconcard not loaded	ENETLOAD	0xFC
Eiconcard halted	ENETHALT	0xFD
Eiconcard driver not installed	ENETNODRV	0xFE
Command not completed	ENETPEND	0xFF