You are here: CSP Hardware Product Descriptions > 5 Internet Protocol Cards > Multi-Function Media I/O Plus Card - CSP-BIO-1400R
Multi-Function Media I/O Plus Card - CSP-BIO-1400R
The Multi-Function Media I/O Plus card is required to provide Ethernet connectivity for the IP Network Interface Series 3 and DSP Series 2 Plus cards. This card connects to the IP Network Interface Series 2 and DSP Series 2 Plus cards through the chassis midplane.
The Multi-Function Media I/O Plus card provides Ethernet ports for the following six 10/100 Base-T Ethernet auto-negotiating signals.
• Two Ethernet control signals that are available for NFS, matrix connectivity, RTP and redundancy
• Four Ethernet data signals that are disabled at this time and reserved for future use
The Multi-Function Media I/O Plus card resides in the rear card slot of a CSP 2090, CSP 2110, or CSP 2040 chassis directly behind the corresponding IP Network Interface Series 2 or DSP Series 2 Plus card.
The part number, serial number, model number, and revision are located on the back of the board.
The Multi-Function Media I/O Plus card is designed to the following electrical, physical, and environmental specifications.
Electrical |
Specification |
---|---|
Supply Voltage, Vcc |
5.00V |
Supply Current, Vcc @ 5.0V |
1.0A (typical) |
Physical |
Specification |
---|---|
Height |
318.5 mm (12.54 in.) |
Depth |
105.2 mm (4.14 in) |
Width |
19.7 mm (0.775 in.) |
Environmental |
Specification |
---|---|
Temperature - Storage |
-40~C to 70~C (-40~F to 158~F) |
Temperature - Operation |
0~C to 50~C (32~F to 122~F) |
Temperature Shock - Storage |
-40~C to 70~C to -40~C (-40~F to 158~F to -40~F) @ 5~C/min. |
Temperature Shock - Operation |
0~C to 50~C (32~F to 122~F) @ |
Humidity - Operating |
5% to 85% |
Altitude |
Up to 4000 m (13,123 ft.) |
The Multi-Function Media Plus I/O card model number is listed below.
Product |
Model No. |
RoHS Model No. |
---|---|---|
Multi-Function Media Plus I/O |
Not Applicable |
CSP-BIO-1400R |
The products related to the Multi-Function Media I/O Plus card are listed below.
Product |
Model No. |
RoHS Model No. |
---|---|---|
DSP Series 2 Plus card with one module |
Not Applicable |
CSP-DSP-1410R |
DSP Series 2 Plus card with two modules |
Not Applicable |
CSP-DSP-1420R |
The front view shows the LEDs, push button switch, and Ethernet connectors.
The table below describes the LEDs as shown in the front view of the Multi-Function Media I/O Plus card.
Fault, Hreset LEDs/Reset Push Button |
Color/Status |
Description |
---|---|---|
Fault |
Off |
Reserved |
Hreset |
Green |
Indicates the I/O card is being reset. |
Reset |
Initiates a reset of the I/O card. |
|
Ethernet LEDs |
Color/Status |
Description |
Activity |
Green |
Indicates both RX (receive) and TX (transmit) activity (20ms on time) |
Off |
Indicates no RX or TX activity |
|
Col/FD (Collision/Duplex) |
Green |
Flashes when collision occurs in half duplex mode (20ms on time) Continuous indication when in full duplex mode Flashes (10 Hz) during continuous collisions |
Off |
Indicates no collisions |
|
LNK (Link) |
Green |
Flashes during auto-negotiation Continuous indication when a link is established Continuously flashes during network misconfiguration |
Off |
Indicates loopback |
|
100M (Speed) |
Yellow |
Indicates 100Base-T (100 Mbps) link established |
Flashes (0.4 sec.) with no link established |
||
Off |
10Base-T (10 Mbps) link not supported |