You are here: CSP Developer’s Guide: Internet Protocols > 3 IP Network Interface Series 2 Card > VoIP Resource Profile Terminal Capabilities
VoIP Resource Profile Terminal Capabilities
VoIP Resource Profiles are categorized by their terminal capabilities. The following tables describe the VoIP terminal capabilities for each IP Network Interface Series 2 card resource profile, including the VDAC-ONE card.
Table 3-7 VDAC-ONE Resource Profile Terminal Capabilities
|
Profile Number |
Profile Name |
Max Spans |
Max Channels |
Max EC Tail |
Max JB Delay |
|||
|
0 |
VDAC-ONE |
1.25 |
40 |
25ms |
300ms |
|||
|
Codecs Supported |
Fax Relay Supported |
Modem Relay Supported |
||||||
|
(0) G.711 A-Law, (1) G.711 m-Law, (2-5)G.726 16, 24, 32, 40Kpbs , (6-14) G.727 16, 16-24, 24, 16-32, 24-32, 32, 16-40, 24-40, 32-40, 40Kpbs, (15) G.723.1 5.3Kbps, (16) G.723.1 6.3Kbps, (17) G.729
|
Yes |
No |
||||||
|
Attribute Name (TLV Tag) |
Length (bytes) |
Default Value |
Valid Values |
Defaults Configurable |
Run-time Configurable |
|||
|
(0x100) RTP Payload Type |
1 |
(1) G.711 m-Law |
See Codecs Supported |
Yes |
No |
|||
|
(0x101) RTP Payload Size |
1 |
(1) 1x |
(1) 1x - (8) 8x |
Yes |
No |
|||
|
(0x102) RTP Silence Suppression |
1 |
(0) Disabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x103) Echo Cancellation |
1 |
(1) Enabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x1C2) Minimum Jitter Buffer Delay |
4 |
75ms |
0 - 150ms, Must be smaller than Maximum JB Delay |
Yes |
No |
|||
|
(0x1C3) Maximum Jitter Buffer Delay |
4 |
150ms |
0 - 300ms, Must be larger than Minimum JB Delay |
Yes |
No |
|||
|
(0x1C4) Adaptation Rate |
1 |
0 - 0xc |
7 |
Yes |
No |
|||
|
(0x1C5) Fax Type |
1 |
(0) Transparent |
(0) Transparent, (1) Relay, (2) Bypass |
Yes |
Before Fax has started |
|||
|
(0x1C7) Bypass Coder Type |
1 |
(1) G.711 m-Law |
See Codecs Supported |
Yes |
Before Fax has started |
|||
|
(0x1D1) RTP Redundancy |
1 |
(0) No Redundancy |
(0) No Redundancy, (1) Level 1 using RFC 2198 |
Yes |
No |
|||
|
(0x1D2) Fax Redundancy |
1 |
(0) No Redundancy |
(0) No Redundancy, (1 - 2) Level 1 to Level 2 |
Yes |
Before Fax has started |
|||
|
Attribute Name (TLV Tag) |
Length (bytes) |
Default Value |
Valid Values |
Defaults Configurable |
Run-time Configurable |
|||
|
(0x1D4) Type Of Service |
1 |
0 |
0 - 0xFE [Precedence (000 - 111), Delay (0-1), Reliability (0-1), Cost (0-1)] |
Yes |
Yes |
|||
|
(0x1DB) Connection Mode |
1 |
(0) Tx/Rx |
(0) Tx/Rx, (1) Tx Only, (2) Rx Only |
No |
Yes |
|||
|
(0x1DF) UDP Source Port Validate |
1 |
(1) Enabled |
0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x1E2) RFC 2833 Enable |
1 |
(0) Disabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x1E6) T.38 SRC UDP Port |
4 |
No Default |
0 – 0xFFFF |
No |
Before Fax has started |
|||
|
(0x1E7) T.38 DST UDP Port |
4 |
No Default |
0 – 0xFFFF |
No |
Before Fax has started |
|||
|
(0x1E8) RTCP SRC UDP Port |
4 |
RTP Port + 1 |
0 – 0xFFFF |
No |
Yes |
|||
|
(0x1E9) RTCP DST UDP Port |
4 |
RTP Port + 1 |
0 – 0xFFFF |
No |
Yes |
|||
|
(0x1EB) RTP Timer |
4 |
(0) Disabled |
0 – 0xFFFF (x 10 ms) |
Yes |
No |
|||
|
(0x1EC) Media InactivityDetection Timeout |
4 |
(0) Disabled |
0 – 0xFFFF (x 10 ms) |
Yes |
No |
|||
|
(0x2794) DST IP ADDR |
4 |
No Default |
IP Address – any valid IP Address |
No |
Yes |
|||
|
(0x2795) DST RTP ADDR |
4 |
No Default |
UDP Port - Any valid IP Port |
No |
Yes |
|||
Table 3-8 IP Network Interface Series 2 Resource Profile
|
Profile Number |
Profile Name |
Max Spans |
Max Channels |
Max EC Tail |
Max JB Delay |
|||
|
1 |
IP Network Interface Series 2: G.711 Only |
16 |
512 |
64ms |
300ms |
|||
|
Codecs Supported |
Fax Relay Supported |
Modem Relay Supported |
||||||
|
(0) G.711 A-Law, (1) G.711 m-Law |
No |
No |
||||||
|
(TLV Tag) Attribute Name |
Length (bytes) |
Default Value |
Valid Values |
Defaults Configurable |
Run-time Configurable |
|||
|
(0x100) RTP Payload Type |
1 |
(1) G.711 m-Law |
See Codecs Supported |
Yes |
Yes |
|||
|
(0x101) RTP Payload Size |
1 |
Coder Dependent |
Coder Dependent. See VDAC-ONE Resource Profile Terminal Capabilities |
Yes |
Yes |
|||
|
(0x102) RTP Silence Suppression |
1 |
(0) Disabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x103) Echo Cancellation |
1 |
(1) Enabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x1C2) Minimum Jitter Buffer Delay |
4 |
75ms |
0 - 150ms, Must be smaller than Maximum JB Delay |
Yes |
No |
|||
|
(0x1C3) Maximum Jitter Buffer Delay |
4 |
150ms |
0 - 300ms, Must be larger than Minimum JB Delay |
Yes |
No |
|||
|
(0x1C5) Fax Type |
1 |
(0) Transparent |
(0) Transparent, (2) Bypass |
Yes |
No |
|||
|
(0x1C7) Bypass Coder Type |
1 |
(1) G.711 m-Law |
See Codecs Supported |
Yes |
No |
|||
|
(0x1D1) RTP Redundancy |
1 |
(0) No Redundancy |
(0) No Redundancy |
Yes |
Yes |
|||
|
(0x1D4) Type Of Service |
1 |
0 |
0 - 0xFE [Precedence (000 - 111), Delay (0-1), Reliability (0-1), Cost (0-1)] |
Yes |
Yes |
|||
|
(0x1DB) Connection Mode |
1 |
(0) Tx/Rx |
(0) Tx/Rx, (1) Rx Only, (2) Tx Only |
No |
Yes |
|||
|
(0x1DF) UDP Source Port Validate |
1 |
(1) Enabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x1E2) RFC 2833 Enable |
1 |
(0) Disabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x1E6) T.38 SRC UDP Port |
4 |
No Default |
0 – 0xFFFF |
No |
Before Fax has started. |
|||
|
(TLV Tag) Attribute Name |
Length (bytes) |
Default Value |
Valid Values |
Defaults Configurable |
Run-time Configurable |
|||
|
(0x1E7) T.38 DST UDP Port |
4 |
No Default |
0 – 0xFFFF |
No |
Before Fax has started. |
|||
|
(0x1E8) RTCP SRC UDP Port |
4 |
RTP Port + 1 |
0 – 0xFFFF |
No |
Yes |
|||
|
(0x1E9) RTCP DST UDP Port |
4 |
RTP Port + 1 |
0 – 0xFFFF |
No |
Yes |
|||
|
(0x1EB) Initial Media Inactivity Detection Timeout |
4 |
(0) Disabled |
0 – 0xFFFF (x 10 ms) |
Yes |
No |
|||
|
(0x1EC) Media InactivityDetection Timeout |
4 |
(0) Disabled |
0 – 0xFFFF (x 10 ms) |
Yes |
Yes |
|||
|
(0x2794) DST IP ADDR |
4 |
No Default |
IP Address – any valid IP Address |
No |
Yes |
|||
|
(0x2795) DST RTP ADDR |
4 |
No Default |
UDP Port - Any valid IP Port |
No |
Yes |
|||
1
Table 3-9 IP Network Interface Series 2 Resource Profile 2 Terminal Capabilities
|
Profile Number |
Profile Name |
Max Spans |
Max Channels |
Max EC |
Max JB Delay |
|||
|
2 |
IP Network Interface Series 2: VDAC-ONE Compatible |
8 |
256* |
64ms |
300ms |
|||
|
Codecs Supported |
Fax Relay Supported |
Modem Relay Supported |
||||||
|
(0) G.711 A-Law, (1) G.711 m-Law, (2-5) G.726, 16Kbps, 24Kbps, 32Kbps, 40Kbps, (15-16) G.723.1 5.3Kbps, 6.3Kbps, (17) G.729 A/B |
Yes |
No |
||||||
|
(TLV Tag) Attribute Name |
Length (bytes) |
Default Value |
Valid Values |
Defaults |
Run-time |
|||
|
(0x100) RTP Payload Type |
1 |
(1) G.711 m-Law |
See Codecs Supported |
Yes |
Yes |
|||
|
(0x101) RTP Payload Size |
1 |
Coder Dependent |
Coder Dependent. See VDAC-ONE Resource Profile Terminal Capabilities. |
Yes |
Yes |
|||
|
(0x102) RTP Silence Suppression |
1 |
(0) Disabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x103) Echo Cancellation |
1 |
(1) Enabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x1C2) Minimum Jitter Buffer Delay |
4 |
75ms |
0 - 150ms, Must be smaller than Maximum JB Delay |
Yes |
No |
|||
|
(0x1C3) Maximum Jitter Buffer Delay |
4 |
150ms |
0 - 300ms, Must be larger than Minimum JB Delay |
Yes |
No |
|||
|
(0x1C5) Fax Type |
1 |
(0) Transparent |
(0) Transparent, (1) Relay, (2) Bypass |
Yes |
No |
|||
|
(0x1C7) Bypass Coder Type |
1 |
(1) G.711 m-Law |
See Codecs Supported |
Yes |
No |
|||
|
(0x1D1) RTP Redundancy |
1 |
(0) No Redundancy |
(0) No Redundancy, (1) Level 1 using RFC 2198 |
Yes |
Yes |
|||
|
(0x1D2) Fax Redundancy |
1 |
(0) No Redundancy |
(0) No Redundancy, (1 - 3) Level 1 to Level 3 |
Yes |
No |
|||
|
(0x1D4) Type Of Service |
1 |
0 |
0 - 0xFE [Precedence (000 - 111), Delay (0-1), Reliability (0-1), Cost (0-1)] |
Yes |
Yes |
|||
|
(0x1DB) Connection Mode |
1 |
(0) Tx/Rx |
(0) Tx/Rx, (1) Rx Only, (2) Tx Only |
No |
Yes |
|||
|
(0x1DF) UDP Source Port Validate |
1 |
(1) Enabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x1E2) RFC 2833 Enable |
1 |
(0) Disabled |
(0) Disabled, (1) Enabled |
Yes |
Yes |
|||
|
(0x1E6) T.38 SRC UDP Port |
4 |
No Default |
0 – 0xFFFF |
No |
Before Fax has started. |
|||
|
(TLV Tag) Attribute Name |
Length (bytes) |
Default Value |
Valid Values |
Defaults |
Run-time |
|||
|
(0x1E7) T.38 DST UDP Port |
4 |
No Default |
0 – 0xFFFF |
No |
Before Fax has started. |
|||
|
(0x1E8) RTCP SRC UDP Port |
4 |
RTP Port + 1 |
0 – 0xFFFF |
No |
Yes |
|||
|
(0x1E9) RTCP DST UDP Port |
4 |
RTP Port + 1 |
0 – 0xFFFF |
No |
Yes |
|||
|
(0x1EB) Initial Media Inactivity Detection Timeout |
4 |
(0) Disabled |
0 – 0xFFFF (x 10 ms) |
Yes |
No |
|||
|
(0x1EC) Media Inactivity Detection Timeout |
4 |
(0) Disabled |
0 – 0xFFFF (x 10 ms) |
Yes |
Yes |
|||
|
(0x2794) DST IP ADDR |
4 |
No Default |
IP Address – any valid IP Address |
No |
Yes |
|||
|
(0x2795) DST RTP ADDR |
4 |
No Default |
UDP Port - Any valid IP Port |
No |
Yes |
|||
* There are a total of 256 channels. However, one channel is used internally for ICMP support leaving 255 channels.
Definitions of Terminal Capabilities
The definitions of the above terminal capabilities are as follows:
The Profile Number is the system-wide identification of the Resource Profile. ID 0 is for VDAC-ONE, IDs 1-3 are for IP Network Interface Series 2.
The Profile Name identifies the profile.
The number of 32-channel spans the profile is capable of supporting.
The number of VoIP Channels the profile is capable of supporting.
The list of Voice codecs supported by this profile. The number prefixed to the codec is the value of the codec used in the PAYLOAD TYPE TLV Attribute.
The Echo Canceller tail length supported by the profile.
The maximum amount of voice data buffered up to reduce jitter.
Indicates whether T. 38 FAX Relay is supported.
Indicates the name and TLV tag of configurable VoIP Channel Attributes.
Indicates the number of bytes for the value in the Attribute TLV.
Indicates the default value assigned to the Attribute TLV upon. initiating a IP Network Interface Series 2 card cold start.
Indicates the range of valid values associated with the Attribute TLV.
Indicates whether or not the host can configure the module-wide default for this Attribute TLV. If so, all subsequent channels will use this value as a default.
Indicates whether or not the host can update the Attribute TLV Value on an active channel.