You are here: CSP API Reference > 3 Information Control Blocks > SS7 and ISDN Values
This section provides data values required for SS7 ICBs, including the following:
• SS7 Parameter IDs
• MTP Statistics Parameter IDs from Q.752
See "SS7 ISUP Message Format Configure 0x6B" for a list of ISUP Message IDs.
The following is a partial list of SS7 parameters. For a complete list and coding, consult the appropriate ANSI or ITU specification.
0x03 |
Access transport |
---|---|
0x27 |
Automatic congestion level |
0x11 |
Backward call indicators |
0xC6 |
Business group |
0x01 |
Call reference |
0x04 |
Called party number |
0x0A |
Calling party number |
0x09 |
Calling party's category |
0xC5 |
Carrier identification |
0xEE |
Carrier selection information |
0x12 |
Cause indicators |
0xEB |
Charge number |
0x0D |
Connection request |
0xC3 |
Egress service |
0x07 |
Forward call indicators |
0xC0 |
Generic address |
0xC1 |
Generic digits |
0x0F |
Information indicators |
0x0E |
Information request indicators |
0xC4 |
Jurisdiction |
0x06 |
Nature of connection indicators |
0xEF |
Network transport |
0xE1 |
Notification indicator |
0x29 |
Optional backward call indicators |
0x28 |
Original called number |
0xEA |
Originating line information |
0x13 |
Redirection information |
0x0B |
Redirection number |
0xE2 |
Service activation |
0xEC |
Service code indicator |
0xED |
Special processing request |
0xE3 |
Transaction request |
0x23 |
Transit network selection |
0x1D |
User service information |
Parameter length for each ID listed below is 0x0004 except where noted.
0x0000 |
MTP3 Timestamp This value is a 1msec resolution, modulus 2^32 timestamp derived from the internal processing logic of MTP3. The datum of this timestamp is established internally by each MTP3 at the time the signalling stack is configured and cannot be set. As presented, the timestamp should only be used for relative timing of MTP3 Q.752 events and reports within a signaling stack. The timestamp for interval reports identify the time associated with the end of the reporting interval and not the time of the actual report. Consequently, host attempts to correlate the timestamp to a time datum must consider only the 1st interval report of a sequence for this correlation. |
0x0001 |
Interval sequence number This value is a modulus 2^32 sequence number which identifies the reporting interval. The initial value for the first reporting interval following start or restart of interval reporting is 1. |
0x0002 |
Duration of the link in-service state |
0x0003 |
Duration of the link unavailable state |
0x0004 |
Duration of the link local inhibit state |
0x0005 |
Duration of the link remote inhibit state |
0x0006 |
Duration of the link failed state |
0x0007 |
Duration of the link remote blocked state |
0x0008 |
Count of link failures |
0x0009 |
Count of link restorations |
0x000A |
Count of link failures due to an abnormal FIBR/BSNR |
0x000B |
Count of link failures due to delayed ACK |
0x000C |
Count of link failures due to error rate |
0x000D |
Count of link failures due to excessive congestion duration |
0x000E |
Count of link failures due to remote LSSU received |
0x000F |
Count of link failures due to link test failures |
0x0010 |
Count of link alignment failures |
0x0011 |
Count of link SUs received in error |
0x0012 |
Count of link NACKs received |
0x0013 |
Count of MSUs transmitted |
0x0014 |
Count of octets transmitted |
0x0015 |
Count of link octets retransmitted |
0x0016 |
Count of MSUs received |
0x0017 |
Count of octets received |
0x0018 |
Duration of inaccessibility |
0x0019 |
Count of MSUs discarded during routing |
0x001A |
Count of MSUs discarded during discrimination |
0x001B |
Counts of UPUs transmitted for each user part (Parameter Length=0x0040) |
0x001C |
Counts of UPUs received for each user part (Parameter Length=0x0040) |
0x001D |
Link failure reason code 0x0001 Abnormal FIBR/BSNR 0x0007 Other |
0x001E |
User part identifier |
ISDN Values
This section provides data values required for ISDN ICBs, including:
• IE Fields
• Cause Codes
Parameter length for each ID listed below is 0x0004 except where noted.
0x0000 |
MTP3 Timestamp This value is a 1msec resolution, modulus 2^32 timestamp derived from the internal processing logic of MTP3. The datum of this timestamp is established internally by each MTP3 at the time the signalling stack is configured and cannot be set. As presented, the timestamp should only be used for relative timing of MTP3 Q.752 events and reports within a signaling stack. The timestamp for interval reports identify the time associated with the end of the reporting interval and not the time of the actual report. Consequently, host attempts to correlate the timestamp to a time datum must consider only the 1st interval report of a sequence for this correlation. |
0x0001 |
Interval sequence number This value is a modulus 2^32 sequence number which identifies the reporting interval. The initial value for the first reporting interval following start or restart of interval reporting is 1. |
0x0002 |
Duration of the link in-service state |
0x0003 |
Duration of the link unavailable state |
0x0004 |
Duration of the link local inhibit state |
0x0005 |
Duration of the link remote inhibit state |
0x0006 |
Duration of the link failed state |
0x0007 |
Duration of the link remote blocked state |
0x0008 |
Count of link failures |
0x0009 |
Count of link restorations |
0x000A |
Count of link failures due to an abnormal FIBR/BSNR |
0x000B |
Count of link failures due to delayed ACK |
0x000C |
Count of link failures due to error rate |
0x000D |
Count of link failures due to excessive congestion duration |
0x000E |
Count of link failures due to remote LSSU received |
0x000F |
Count of link failures due to link test failures |
0x0010 |
Count of link alignment failures |
0x0011 |
Count of link SUs received in error |
0x0012 |
Count of link NACKs received |
0x0013 |
Count of MSUs transmitted |
0x0014 |
Count of octets transmitted |
0x0015 |
Count of link octets retransmitted |
0x0016 |
Count of MSUs received |
0x0017 |
Count of octets received |
0x0018 |
Duration of inaccessibility |
0x0019 |
Count of MSUs discarded during routing |
0x001A |
Count of MSUs discarded during discrimination |
0x001B |
Counts of UPUs transmitted for each user part (Parameter Length=0x0040) |
0x001C |
Counts of UPUs received for each user part (Parameter Length=0x0040) |
0x001D |
Link failure reason code 0x0001 Abnormal FIBR/BSNR 0x0007 Other |
0x001E |
User part identifier |
Formatted IEs with Event include IE data fields. The data included in the format depends on the IE type. The data fields for each IE type is listed below. For more information on IE field values, refer to the API Developer’s Guide: Common Channel Signaling.
0x13 Directory Number (DN) Provisioning
0x04 Autonomous Signaling Sequence
0x0D Disable Autonomous Acknowledge
Parameter Type Values for Cadence Ringing Extended IE
0x10 Cadence Ringing Extended (Type A - Digits and Characters Present)
0x10 Cadence Ringing Extended (Type B - Digits Present, Characters Missing )
0x10 Cadence Ringing Extended (Type C - Digits Missing, Characters Present)
0x10 Cadence Ringing Extended (Type D - Digits and Characters Missing)